|
|
AzzaD
Member Since: 20 Nov 2013
Location: London
Posts: 83
|
Paid.
|
 22nd May 2019 12:52 pm |
|
|
Steamyrotter
Member Since: 03 Jul 2017
Location: Somewhere near Somewhere else in Somerset
Posts: 117
|
Paid with Thanks
👍👍 If things were meant to be easy, then I will soon complicate them....
Please note...
Anything I say is only from my personal experience and knowledge..
I don't assume to know everything, and know there is a lot I don't know..
But then I could be talking  .. O
|
| 22nd May 2019 3:26 pm |
|
|
|
|
NC500
Member Since: 18 Sep 2017
Location: On the NC500
Posts: 541
  
|
Paid!! 
|
| 22nd May 2019 3:35 pm |
|
|
|
|
Gworks
Member Since: 06 Nov 2011
Location: North West
Posts: 34
|
Arrived safe and sound and on time Dan!! Have a good holiday!
Kind Regards
Graham
|
| 24th May 2019 3:04 pm |
|
|
Steamyrotter
Member Since: 03 Jul 2017
Location: Somewhere near Somewhere else in Somerset
Posts: 117
|
Same here
Just need to fit it now
Many thanks for the excellent offer and delivery.
😉😉👍 If things were meant to be easy, then I will soon complicate them....
Please note...
Anything I say is only from my personal experience and knowledge..
I don't assume to know everything, and know there is a lot I don't know..
But then I could be talking .. O
|
| 24th May 2019 5:51 pm |
|
|
NC500
Member Since: 18 Sep 2017
Location: On the NC500
Posts: 541
|
Arrived today Dan- thanks. However, I have searched the forum for fitting instructions for my 2014 D4 (rotary gear selector) and can find no instructions specific for this model. There are several versions on how to fit the fridge all mixed up across several posts but there appear to be none for the late model D4. Can you or anyone help?
Thanks
|
| 28th May 2019 4:14 pm |
|
|
Steamyrotter
Member Since: 03 Jul 2017
Location: Somewhere near Somewhere else in Somerset
Posts: 117
|
For 2014 D4
Remove cup holders (pull up)
Remove 2 screws on water spreader plate and take that out.
Open cubby box lid.
Pull up rear of centre console (through cup holder slot)
Look at cubby box and remove 2 torx screws (lift centre console at rear you don’t need to remove it fully!
Remove the 2 trim pieces on cubby lid hinges.
Put hand below cubby and pry out - it’s a push fit.
Look in bottom of hole and you’ll see the required cable.
Hoof this out of the way.
Push fridge in hole and plug it in.
Then reverse above to fit everything back in.
Takes less than 30 mins to do it.
Cheers If things were meant to be easy, then I will soon complicate them....
Please note...
Anything I say is only from my personal experience and knowledge..
I don't assume to know everything, and know there is a lot I don't know..
But then I could be talking .. O
|
| 28th May 2019 4:58 pm |
|
|
NC500
Member Since: 18 Sep 2017
Location: On the NC500
Posts: 541
|
Thanks but I saw this post elsewhere . The instruction “Remove 2 screws on water spreader plate and take that out” doesn’t seem to apply to my car, there are no screws holding the plastic cup holder assembly in place (once the removable cup holders have been pulled out). Stalling on step 2 kinda screws this as a set of instructions!!!!
|
| 28th May 2019 6:17 pm |
|
|
Steamyrotter
Member Since: 03 Jul 2017
Location: Somewhere near Somewhere else in Somerset
Posts: 117
|
When you take the 2 removable cup holders out you then pull the holder tray out.
That’s a push fit too.
Follow the first 30 seconds of this video.
It IS the same for ours to that point..
If things were meant to be easy, then I will soon complicate them....
Please note...
Anything I say is only from my personal experience and knowledge..
I don't assume to know everything, and know there is a lot I don't know..
But then I could be talking .. O
|
| 28th May 2019 7:06 pm |
|
|
NC500
Member Since: 18 Sep 2017
Location: On the NC500
Posts: 541
|
That’s great, thank you for taking the time to help me. I will attack the D4 tomorrow!
|
| 28th May 2019 9:04 pm |
|
|
Steamyrotter
Member Since: 03 Jul 2017
Location: Somewhere near Somewhere else in Somerset
Posts: 117
|
No prob
I was a bit cautious too but it is easy once you know how
Good luck
👍👍 If things were meant to be easy, then I will soon complicate them....
Please note...
Anything I say is only from my personal experience and knowledge..
I don't assume to know everything, and know there is a lot I don't know..
But then I could be talking .. O
|
| 28th May 2019 9:52 pm |
|
|
CIO
Member Since: 06 Mar 2018
Location: Bahrain
Posts: 109
 
|
Mine arrived yesterday, thanks Dan!
Thanks Steeamy for the instructions. Can't really say i'm looking forward to fitting it 
|
| 29th May 2019 7:47 am |
|
|
