Advertise on DISCO4.COM
Forum · Gallery · Wiki · Shop · Sponsors
DISCO4.COM > Faults & Fixes (D4)

D4 telling me to apply parking brake?
Post Reply  Down to end
Page 1 of 1
jamez79
 


Member Since: 03 Sep 2018
Location: Staffordshire
Posts: 595

United Kingdom 2012 Discovery 4 3.0 SDV6 XS Auto Indus SilverDiscovery 4
D4 telling me to apply parking brake?

Hi all,

Serviced my discs pads and shoes today. Had a squeel a while ago so didn't use the parking brake until I'd replaced and adjusted etc.

Went to put it in bedding in mode and couldn't.

Despite me using the motor without applying the parking brake for two weeks and no warnings on the dash, today after starting the vehicle, it states "apply parking brake" and I get a flashing red P on the dash.

Applied the brake, squeals but doesn't apply the brake. Can still drive forward and back without any sign of the parking brake being on.

I tested the emergency pull release and there's no resistance at all, but that might be because the p brake isn't on?

The flashing light is baffling me, as it didn't flash before, so I'm guessing it's telling me it might not be latched? Hence the no resistance on the emergency cable?

Any ideas?

Thanks
   
Post #238362415th Dec 2024 6:29 pm
View user's profile Send private message View poster's gallery Reply with quote
jamez79
 


Member Since: 03 Sep 2018
Location: Staffordshire
Posts: 595

United Kingdom 2012 Discovery 4 3.0 SDV6 XS Auto Indus SilverDiscovery 4

Arghhh,

So I've taken the disc back off and the epb cable has slipped through the securing clip (held by the spring) and retracted.

How do I get that back out?

I can see the cable and the tip but pulling it does nothing.

Anything I can do with an id tool?

Cheers
   
Post #238366016th Dec 2024 10:06 am
View user's profile Send private message View poster's gallery Reply with quote
Bardley
 


Member Since: 02 May 2018
Location: Hertfordshire
Posts: 478

United Kingdom 2011 Discovery 4 3.0 TDV6 HSE Auto Santorini BlackDiscovery 4

Morning chap.
The cable is held by the clip, and the spring holds this in place; easy to get this wrong and out of line.
It sounds like the cable is in the applied position (but there may now be issues after you've pulled the emergency release cable?)
I'd now have a pair of molegrips on that cable and pull while someone releases the EPB to turn handbrake off. It may come out.
Did you use the brake bible and set the shoes to Mount mode before the work?
Shoes have to be adjusted correctly or the EPB over-reaches itself and can create problems.
The gear position is related to what the EPB is doing, and it will shout at you if you try to leave it out of Park, handbrake off etc.
Maybe read the faults and see what you have.
Getting that cable out might need a rematch if the emergency cable has been pulled though... First things first.
Good luck.
 2011 MY D4 HSE
Previously 2001 D2 TD5, 1996 D1 300Tdi, 1985 90 2.2 petrol.
Bikes! KTM, BMW, British, Classics and others.
 
 
Post #238366416th Dec 2024 11:03 am
View user's profile Send private message View poster's gallery Reply with quote
jamez79
 


Member Since: 03 Sep 2018
Location: Staffordshire
Posts: 595

United Kingdom 2012 Discovery 4 3.0 SDV6 XS Auto Indus SilverDiscovery 4

Cheers for the reply mate.

I tied the "pull like hell while the epb is released" sounded stuck so tried the unjam on the IID. No joy.

I've now taken the epb cover off and freed the brass rod and it unjams on the tool now so hopefully once reassembled, making sure the clasp stays in place this time, I'll see how it goes. Then just to reapply silicone and put the cover back. What a stupid place to put the epb. Crying or Very sad
   
Post #238366816th Dec 2024 11:34 am
View user's profile Send private message View poster's gallery Reply with quote
eightfoot
 


Member Since: 12 Apr 2015
Location: sunny essex
Posts: 810

United Kingdom 2005 Discovery 3 TDV6 S Auto Bonatti GreyDiscovery 3

the way i sorted mine was to strip all the shoes out from the hub then i connected a shoe to the cable and with g clamp put pressure on the shoe via the hub then i applied the handbrake then i used the iid to select the service mode which then wound the cable fully out

i prob haven't explained it very well but you need tension on the cable before the iid can unwind the cable
 please excuse any grammer/punctuation mistakes,i'm thick,thankyou
current vehicles 2005 d3 2013 d4 
 
Post #238368016th Dec 2024 5:46 pm
View user's profile Send private message View poster's gallery Reply with quote
jamez79
 


Member Since: 03 Sep 2018
Location: Staffordshire
Posts: 595

United Kingdom 2012 Discovery 4 3.0 SDV6 XS Auto Indus SilverDiscovery 4

Hi, that makes sense to me.

That probably would've worked if I hadn't jammed the brass rod against the nut at the end. Took a sharp tap with a mallet to free it off and then I could unwind it.

All back together and working. Very Happy

Just the air suspension to sort now. Big Cry
   
Post #238368316th Dec 2024 6:04 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO4.COM is independent and not affiliated to Land Rover.
Switch to Mobile Site