Advertise on DISCO4.COM
Forum · Gallery · Wiki · Shop · Sponsors
DISCO4.COM > Maintenance & Mods (D3)

discovery 3 2007 service indicator
Post Reply  Down to end
Page 1 of 1
monkey9871
 


Member Since: 21 Nov 2019
Location: Solihull Westmidlands
Posts: 17

United Kingdom 2007 Discovery 3 TDV6 GS Auto Indus SilverDiscovery 3
discovery 3 2007 service indicator

HI there hope everyone is doing well. Dose any one now how to switch off service indicator on a discovery 3 manually THANKS when i switch on the ignition service lndicator come on then gose off dose not stay on THanks Sad Sad Sad
  
Post #21349675th Apr 2020 6:32 am
View user's profile Send private message View poster's gallery Reply with quote
enb54
 


Member Since: 11 May 2019
Location: Red Deer, Alberta
Posts: 105

Canada 2007 LR3 4.0 V6 Petrol SE Auto Stornoway GreyLR3

I had this in some original documentation I got from one of the forums, but can't remember where so I can't credit it properly. I don't really know if it works or not, so be careful! Maybe someone else can chime in...

Manual Reset Procedure

• Press and hold the trip reset button.
• Turn the ignition switch on to the ignition position II.
• If the SII function is set in the CCF the information display will flash 'SERVICE' for 5 seconds and then display 'SERVICE' constantly. If the SII function is not set in the CFF the information display will show the normal odometer and trip information.
• The software will check if remaining distance service is enabled (threshold reached). If the remaining distance service is not enabled the procedure will continue from step K.
• If the trip reset button is released within 10 seconds of entering the reset mode, the information display will show 'OIL'.
• If the trip reset button is not released after 10 seconds, the display will show the next service type and distance/days to next service and the instrument cluster will exit the manual reset procedure.
• If the oil service value reset is not required, press the trip reset button within 10 seconds of releasing it in step E and hold for less than 5 seconds and proceed to step H. This will by-pass the oil service reset procedure.
• If the oil service value is to be reset, press the trip reset button within 10 seconds of releasing it and hold for more than 5 seconds. The information display will show 'RESET' for 5 seconds and then reset the oil service value.
• If reset is not possible, the information display will show 'CANNOT RESET' for 5 seconds.
• The information display will show 'INSPECT'.
• If the inspection service value reset is not required, press the trip reset button within 10 seconds of releasing it in step G and hold for less than 5 seconds and proceed to step K. This will by-pass the inspection service reset procedure.
• If the trip reset button is not pressed after 10 seconds, the display will show the next service type and distance/days to next service and the instrument cluster will exit the manual reset procedure.
• If the inspection service value is to be reset, press the trip reset button within 10 seconds of releasing it and hold for more than 5 seconds. The information display will show 'RESET' for 5 seconds and then reset the inspection service value.
• If reset is not possible, the information display will show 'CANNOT RESET' for 5 seconds.
• The software will check if date service is enabled (threshold reached). If the date service is not enabled the procedure will continue from step O.
• The information display will show 'DATE'.
• If the date service value reset is not required, press the trip reset button within 10 seconds of releasing it in step I and hold for less than 5 seconds and proceed to step O. This will by-pass the date service reset procedure.
• If the trip reset button is not pressed after 10 seconds, the display will show the next service type and distance/days to next service and the instrument cluster will exit the manual reset procedure.
• If the date service value is to be reset, press the trip reset button within 10 seconds of releasing it and hold for more than 5 seconds. The information display will show 'RESET' for 5 seconds and then reset the date service value.
• The information display will show 'END'.
• If the trip reset button is pressed within 10 seconds and pressed for less than 5 seconds the procedure will return to step E.
• If the trip reset button is not pressed after 10 seconds, the display will show the next service type and distance/days to next service and the instrument cluster will exit the manual reset procedure.
• If the trip reset button is pressed within 10 seconds and pressed and held for more than 5 seconds the information display will show the next service type and distance/days to next service and the instrument cluster will exit the manual reset procedure.

Hope this helps a bit, or at least points you in the direction required. I use the IIDTool...
 1967 Ford Bronco 289 V8 (1968)
1974 Toyota FJ55 3.9L I6 (1975)
1984 Chev K5 Blazer Camper 400 V8 (1989)
2006 Nissan X-Trail Bonaventure 2.5L I4 (2007)
2007 Land Rover LR3 4.0L V6 (2019) 
 
Post #21352285th Apr 2020 6:21 pm
View user's profile Send private message View poster's gallery Reply with quote
monkey9871
 


Member Since: 21 Nov 2019
Location: Solihull Westmidlands
Posts: 17

United Kingdom 2007 Discovery 3 TDV6 GS Auto Indus SilverDiscovery 3

Thanks for all your help will try THANKS Smile Smile Smile Smile Smile
  
Post #21353186th Apr 2020 5:06 am
View user's profile Send private message View poster's gallery Reply with quote
Globetrotter448
 


Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1771

Australia 2007 Discovery 3 4.0 V6 Petrol SE Auto Java BlackDiscovery 3

A tool is simpler Embarassed
  
Post #21353916th Apr 2020 11:27 am
View user's profile Send private message View poster's gallery Reply with quote
monkey9871
 


Member Since: 21 Nov 2019
Location: Solihull Westmidlands
Posts: 17

United Kingdom 2007 Discovery 3 TDV6 GS Auto Indus SilverDiscovery 3
oil pump

Hi everyone i have a discovery 3 tdv6 2007 it has the discovery 4 service kit on it different fuel filter would it have the new reinforced oil pump on it Or would it be the old weak one MANY THANKS Gary
  
Post #219547922nd Dec 2020 8:48 am
View user's profile Send private message View poster's gallery Reply with quote
Sea Raider
 


Member Since: 01 Nov 2016
Location: None
Posts: 4450


Only way to find out is either have documentation to prove its been done or get in there and confirm by visually inspecting the pump and best to do it sooner rather than later Thumbs Up
  
Post #219548522nd Dec 2020 9:20 am
View user's profile Send private message View poster's gallery Reply with quote
Globetrotter448
 


Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1771

Australia 2007 Discovery 3 4.0 V6 Petrol SE Auto Java BlackDiscovery 3

Have a look at the front of the engine and see if it has the reinforced bit
  
Post #219548622nd Dec 2020 9:20 am
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO4.COM is independent and not affiliated to Land Rover.
Switch to Mobile Site