Advertise on DISCO4.COM
Forum · Gallery · Wiki · Shop · Sponsors
DISCO4.COM > Technical (D3)

Fuel Burning heater - how long should it come on for
Post Reply  Down to end
Page 3 of 3 <123
Landylad
 


Member Since: 23 Dec 2008
Location: Aberdeenshire
Posts: 366

Scotland 2012 Discovery 4 3.0 SDV6 GS Auto Zermatt SilverDiscovery 4

wiggs wrote:
dark.soul999 wrote:
Hi, when a fault is stored in FBH is not possible to clear without IDS (or other diagnostic tool). Big Cry


Whistle

The error lockout mode can be cleared using T4, or by disconnecting the battery power supply
(connector C0926) for a minimum of 10 seconds.


Hey Wiggs.... which one is this?

Cheers.
 If in doot, flat oot!!  
Post #41946010th Feb 2009 9:51 pm
View user's profile Send private message View poster's gallery Reply with quote
wiggs
 


Member Since: 03 Sep 2006
Location: Manchester
Posts: 14368

United Kingdom 2015 Discovery 4 3.0 SDV6 HSE Auto Fuji WhiteDiscovery 4

The one i mentioned on the first page of this thred ..2 pin one with purple wire ( power connector )
 G4 Gone ...but not forgotten  
Post #41947910th Feb 2009 9:58 pm
View user's profile Send private message View poster's gallery Reply with quote
Landylad
 


Member Since: 23 Dec 2008
Location: Aberdeenshire
Posts: 366

Scotland 2012 Discovery 4 3.0 SDV6 GS Auto Zermatt SilverDiscovery 4

Ah, ok Wiggs... that's the one I was disconnecting (eventually, after disconnecting the other two to start). Incidentally, I Censored the connector pulling it off and had to Areldite it back on again Rolling Eyes I don't think that's gonna do me any favours.

In any event, the disconnect didn't return any remedy, although I'm not doubting that it works for some.

What's T4?
 If in doot, flat oot!!  
Post #41951110th Feb 2009 10:25 pm
View user's profile Send private message View poster's gallery Reply with quote
wiggs
 


Member Since: 03 Sep 2006
Location: Manchester
Posts: 14368

United Kingdom 2015 Discovery 4 3.0 SDV6 HSE Auto Fuji WhiteDiscovery 4

Landrover computer the dealer uses
 G4 Gone ...but not forgotten  
Post #41953310th Feb 2009 10:41 pm
View user's profile Send private message View poster's gallery Reply with quote
Landylad
 


Member Since: 23 Dec 2008
Location: Aberdeenshire
Posts: 366

Scotland 2012 Discovery 4 3.0 SDV6 GS Auto Zermatt SilverDiscovery 4

I presume a reset of the FBH can only be done by a LR dealer or can anyone with a computer analyser do it?
 If in doot, flat oot!!  
Post #41953510th Feb 2009 10:46 pm
View user's profile Send private message View poster's gallery Reply with quote
sopjas
 


Member Since: 31 Dec 2008
Location: Its never Dull in Hull
Posts: 280

United Kingdom 2005 Discovery 3 TDV6 S Manual Buckingham BlueDiscovery 3

If your worries that the FBH is faulty any webasto dealer can unplug land rover wiring and connect a tester wich will fire your FBH up independ. This is what i did £50 wasted they then told me because it takes readings from the ecu plus other sensors that the reset at the dealers was a must. My local dealer told me it was an update because of all the problems in the past? Vehicle out of warranty but still carried out F.O.C .

Hope you get to the bottom of it Landylad Thumbs Up
  
Post #41958210th Feb 2009 11:27 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 3 of 3 <123
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO4.COM is independent and not affiliated to Land Rover.
Switch to Mobile Site