Member Since: 05 Jun 2011
Location: Kineton
Posts: 3372
Iid BT AIRBAG LIVE VALUES....SEAT TRACK SENSOR??
Still chasing the airbag light problem
It has been suggested to look at my airbag live values..
I would if I could, but iid BT cannot find any at all?
Not even an option to click on the airbAg/srs ecu
Can this mean it’s fudged? And need replacing
I’ve checked under the seats 1001 times now (previous owner says srs light came on after he messed about under the passenger seat to fix sat nav dvd)
Help
[/i]
Last edited by yogi972 on 25th Jul 2018 9:40 pm. Edited 1 time in total
17th Jul 2018 11:07 pm
IndusD4
Member Since: 01 Dec 2011
Location: Sydney, NSW
Posts: 308
My guess is the IIDTool can show the live values for the suspension airbags only, not the SRS ones.
Ron2016 D4 TDV6 Corris Grey
IIDTool BT
18th Jul 2018 10:20 am
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10365
That don't look an easy fix !
1) When you turn the ignition on, check the orange airbag2 light comes on, in the center console by lock switches.
2) The seat wiring is at the front of the seat. THere is a large connector with 1 bolt. Inside this are smaller plugs. 2 of which are airbag. orange and yellow plugs from memory. You may want to inspect.
3) think I would be trying to find a new airbag ecu
18th Jul 2018 10:48 am
yogi972
Member Since: 05 Jun 2011
Location: Kineton
Posts: 3372
Hi there
Yes the orange airbAg light by switches comes on then off
It stays on if I deactivate passenger airbag, (which I know is correct)
I’ve checked all plugs I can see/reach, the one with the nut has been taken off and squirt of wd40 on contacts, I’ve even unclipped the part from the seat frame to check the rear.
A member on here has shown me screen shot of his live values for srs air bags which pointed to his problem (missing airbag curtain)
you can look at SRS Airbbag live values - i've done it several times to find a dodgy airbag...Si
2016 Disco 4 SE Tech
2019 Fiesta ST3
2021 GBS Zero
18th Jul 2018 10:00 pm
yogi972
Member Since: 05 Jun 2011
Location: Kineton
Posts: 3372
New rotary coupling just fitted..
Kin hate undoing those connections
Still airbag light on
Still cannot complete fault clearance on airbag
Vehicle scanned on 19-07-2018 19:13
Using IIDTool BT V3.0 B2481
Airbag
B1A00-16 (2C) Control module - General electrical failure - circuit voltage below threshold
( at 173367 mi )
U0073-88 (2C) Control module communication bus off - Bus signal/message failure - bus is off
( at 176674 mi )
B00D2-87 (2C) Restraint system malfunction indicator 1 - Bus signal/message failure - missing a message
U0155-87 (2C) Lost communication with instrument cluster control module - Bus signal/message failure - missing a message
U0122-87 (2C) Lost communication with vehicle dynamics control module - Bus signal/message failure - missing a message
U0300-55 (AC) Internal control module software incompatibility - System programming failure - is not configured
B1A55-14 (2C) Crash record output circuit - General electrical failure - circuit short to ground or open
( at 178165 mi )
Engine TDV6
P0405-00 (2D) Exhaust gas recirculation sensor A - circuit low
P0578-00 (28) Speed control multi-function input A circuit is stuck
Ventilation
B1B74-00 (6C) Front foot-defrost mode stepper actuator
( at 179456 mi )
B1B75-00 (6C) Front foot-face mode stepper actuator
( at 179456 mi )
B1B76-00 (6C) Front left air blend stepper actuator
( at 179456 mi )
B1B77-00 (6C) Front right air blend stepper actuator
( at 179456 mi )
At least I got to dust out the nooks n crannys behind the steering wheel
19th Jul 2018 7:46 pm
Dan1720v
Member Since: 28 Mar 2018
Location: Street/Somerset
Posts: 176
To me all those moessages relate to the airbag module not having power/earth. As such the CANbus is missing a link, and the rest of the messages relate to that except for the crash message. Not sure about LE, but most other manufacturers will lock/brick the module if there is a impact related trigger.
19th Jul 2018 8:26 pm
kajtzu
Member Since: 11 Aug 2017
Location: Helsinki
Posts: 6573
Have you looked at your battery? Pete K told me once that the stepper actuator messages appear if the battery is weak, can be ignored as the vehicle is just too sensitive.
19th Jul 2018 8:28 pm
yogi972
Member Since: 05 Jun 2011
Location: Kineton
Posts: 3372
Battery is brand new
I’m having the centre console out to check wiring as hdc button does not work either
Which is in same area as the airbag ecu (I think )
Thankyou for your input guys
19th Jul 2018 8:36 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13648
Just quickly and as mentioned ref the earth wire, check when u remove the centre console to look at the SRS ecu
Also the wires on the passenger side that’s sits under the sill plate
Hope u don’t mind me saying , don’t unplug any SRS wires unless you’ve disconnected the battery first and waited 30 x mins
When I replaced my airbags etc I then used the iid and it allowed me to reset the SRS ecu to normal state from crash data log
Click image to enlarge
19th Jul 2018 11:27 pm
PatGAPInnov Site Sponsor
Member Since: 02 Dec 2011
Location: Montreal
Posts: 745
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum