Member Since: 04 Aug 2015
Location: Internet
Posts: 270
D4 window switches on D3
I am putting D4 door cards on the D3. The only problem is the window switches are different. Does anyone have a wiring diagram for the D4 electric windows please? If anybody has successfully done this or has a good workaround?
Member Since: 24 Oct 2007
Location: Oireland
Posts: 4286
Re: D4 mirror switches on D3
Irwin wrote:
I am putting D4 door cards on the D3.
What state are the D3 cards in ? A happy childhood ... is the worst possible preparation for life.
19th Nov 2015 1:04 pm
DaveJLBI
Member Since: 07 Mar 2014
Location: Clare
Posts: 679
Watching this closely as I have a set of door cards from a D4 too that I want to fit, to match my D4 seats (well, front cushions and leather on my D3 electric frames and full rear D4 seats).
Have you got the door pulls to work? I was just going to swap the switch blocks and get some upholsterer or other to put a small finishing piece. The main difference is the drivers switch block from memory.
19th Nov 2015 3:19 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
The thread should have been "D4 window switches on D3" but anyway, thank you naks, i found the wiring diagram and the D4 use a separate control module for each window switch. The easiest solution would be yours Dave, stick a surround trim on the D3 switches. There are chrome surrounds available for the D4 switches, something like that to make the D3 switch the same size as the D4 switch would do. Is there any company in the uk that makes these sort of things?
22nd Nov 2015 11:19 am
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
Got 3 of the switches sorted. Removed the button from D3 switch, made the hole bigger with a small file and hot glued it in place. Happy with the result, looks original. Now just need to figure out how to do the drivers switch.
19th Aug 2016 10:33 am
DaveJLBI
Member Since: 07 Mar 2014
Location: Clare
Posts: 679
Must have a look later, thanks
19th Aug 2016 11:37 am
dennyrol
Member Since: 27 Jul 2015
Location: Moscow
Posts: 58
Irwin wrote:
Got 3 of the switches sorted. Removed the button from D3 switch, made the hole bigger with a small file and hot glued it in place. Happy with the result, looks original. Now just need to figure out how to do the drivers switch.
Good afternoon! How did you make the block buttons on the driver's side?
22nd Sep 2016 4:36 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
I didnt figure out what to do with the drivers side yet. Still searching for a solution.
22nd Sep 2016 6:05 pm
dennyrol
Member Since: 27 Jul 2015
Location: Moscow
Posts: 58
Side door lock lock button turned out to connect?
22nd Sep 2016 8:18 pm
dennyrol
Member Since: 27 Jul 2015
Location: Moscow
Posts: 58
Irwin wrote:
I didnt figure out what to do with the drivers side yet. Still searching for a solution.
You can ask to do bigger pictures button, that would be seen as you have cut a doorway
22nd Sep 2016 8:29 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
I don't have any other pictures. I used a small file and very gently filed the back of the D4 switch hole back and a little at each side. And filed the bottom of the finger hole forward so the button fits in. Underneath there is a screw hole where the D4 button screw goes. I twisted this off with a pliers so the D3 button fits in.
The lock/unlock buttons work aswell. 3 wires to connect to the centre console lock/unlock switch.
On the door switch, (pin 1) goes to (pin 4 pink/red) on centre console. (Pin 2) goes to (pin 10 yellow/pink) and (Pin 5) is an earth wire (pin 15 black) or any black earth wire nearby
Just the bloody drivers window switch to sort out now
23rd Sep 2016 10:08 pm
dennyrol
Member Since: 27 Jul 2015
Location: Moscow
Posts: 58
Thank you Irwin for the answer!
Irwin, only three wires? Lighting buttons lock / unlock the door also work?
About the connect buttons from the discovery 4, we have, by one master, was able to get to work on the buttons from discovery 4 on the passenger door. It remains only to deal with the driver's door. For this I had to buy a window motor from a discovery 4 and the wiring on the door from the discovery 4. We have applied to the unit of comfort that is located in the middle of the door card voltage activated K - bus. Rear door, window regulator earned! Work on. As something, write.
24th Sep 2016 9:31 am
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
For light on the lock buttons a wire goes to pin 4. Can be taken from small red wire on the window switch. Same with the mood lighting on the door handles.
24th Sep 2016 10:58 am
dennyrol
Member Since: 27 Jul 2015
Location: Moscow
Posts: 58
Thank you . And You understand what we've got to get to work original button from discovery 4, no alterations? Now working, above the driver's buttons. It's all in the unit of comfort in the door lining, and through him all can be made to work.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum