Member Since: 22 Sep 2016
Location: Darlington
Posts: 96
Scrapping & Banging whilst driving around a round-about
Tonight on my way to work, right hand lock driving round a round-about there's a load scrapping noise and banging coming from the front. Resistance coming back to the engine as had to apply throttle to keep going round.
straight line ok no noise, hub bearing maybe ?Discovery 3 2007 HSE
9th Feb 2017 11:16 pm
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
DSC kicking in?Land Rover - Turning Drivers into Mechanics Since 1948
Member Since: 23 Nov 2016
Location: Stoke on Trent
Posts: 4
Scrapping & Banging whilst driving around a round-about
Had a similar problem this weekend towing my caravan down an incline at 40 - 45 mph and a left hand bend, scrapping noise and DSC light came on at the same time then went off as I straightened up. It repeated on the next left hand bend so I slowed for the next similar bend, ok on right bends. Switched DSC off until I reached my destination. D3 drives OK without caravan on, obviously not loading it the same? Any clews? I'll get under the D3 at the weekend but too busy at the mo.
21st Feb 2017 9:58 pm
waterbuoy
Member Since: 26 Oct 2013
Location: Argyll
Posts: 2896
Check your tyre pressures - had the same issue in the alps last week and stopped to find a slow puncture in one of rear tyres that was causing DSC to kick in Currently 2009 Disco 3 SE, 2013 MY D4 HSE and 2016 D4 SE
Previously:
TD5 Defender 110 CSW (230k miles)
300TDi Disco 1 (289k)
4 RR Classics (300-350k each, 2 manual, 2 auto)
110 V8 CSW (220k)
S3 109 hi cap pickup (ex RN)
S2A 88 Safari SW with lpg conversion (bloody lethal)
21st Feb 2017 10:02 pm
Alan B
Member Since: 12 Feb 2013
Location: Fife
Posts: 6528
Either wheel bearing or upper rear bush.
Mine does exactly that but on right hand bends, so weight transfers to left hand side of d3
Exactly what mine is going to disco Mikey for on Friday, rr sport arms and bushes and a wheel bearing
D3 57 xs Stornaway grey
D2 02 commercial silver gone but a great servant and won't be forgotten
Iid Bluetooth
21st Feb 2017 11:18 pm
Danlor
Member Since: 23 Nov 2016
Location: Stoke on Trent
Posts: 4
Mine has had new front lower arms both sides June 2016 and the tyre pressures are good, so I'll check wheel bearings and the other bushes..
The noise seamed to be O/S/F..
Have notice a rattle at the front on rough ground as if something loose there!
22nd Feb 2017 2:08 pm
Danlor
Member Since: 23 Nov 2016
Location: Stoke on Trent
Posts: 4
Scrapping & Banging whilst driving around a round-about
Just had new off side lower wishbone fitted as the rear bush was shot.
Had both arms done and wheel alignment done
Think the previous owner was stung!!!
Just need to sort out intermittent suspension height fault coming on.
Use normal height only.
Any clews???
20th Apr 2017 10:56 pm
Geoff at Drym
Member Since: 18 May 2015
Location: Cornwall
Posts: 584
Scrapping and banging?? What, are you having a fight with someone or something?2007 Disco3 2.7 tdv6 SE
gvif with reversing camera
V8 brakes with new EPB module and shoes
Later D4 grille
Alive tuning remap
Mazda MX5
Ferguson ted20 tractor
Hyundai Getz 1.4 (wife's )
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum