Member Since: 02 Feb 2014
Location: limerick
Posts: 11
New Height Sensors +compressor still not working
Evening all, I am having issues with my suspension after installing new sensors and compressor on start up after Installation back rises to extended mode but front stays on bump stops ive checked the valve block before air resevoir and front valve black and cleaned as needed!! Could this be a recalibrate issue only i have it going to indy on tuesday but would like to have an idea before i get there!!?? Is there anything else worth checking?? Any help appreciated
31st May 2018 9:53 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4658
Hi
Can you provide a bit more backround information / reasons for the work carried out? (fault codes)
Did you replace the compressor with the same make, or a different one? eg Hitachi / AMK
Did you change all four height sensors, or just the front? Did you change the compressor relay ?
The more detail you can provide the more accurate and tailored the response is likely to be!
1st Jun 2018 1:43 am
murchu4
Member Since: 02 Feb 2014
Location: limerick
Posts: 11
I had been getting intermittent suspension faults such as slow to rise normal height only and had bought a hitatchi replacement awhile back in view of replacing.. Then i had faulty nsf height sensor so decided then to do the whole lot in one go.. I did have white dust in in valve block at resevoir and front but bothhave been cleaned.. Now i have the torpedo look with back extended and front on bump stop....(I also changed relax)
1st Jun 2018 7:50 am
G_Cam
Member Since: 12 Aug 2010
Location: Fife
Posts: 2048
Try fitting new seals in the valve blocks.
Then re-calibrate the suspension..
And double check for air leaks...
That should sort it 1 TR6 Rusting away quietly
1 FARR UTV SOLD
1 International Harvester SOLD
7 x D3 all SOLD
2 x D4 both SOLD
1 x Mrs D4 'Panther' SOLD
1 x Outlander van SOLD
1 continual stream of car parts and me living in the garage...
1st Jun 2018 8:17 am
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4658
murchu4 wrote:
I had been getting intermittent suspension faults such as slow to rise normal height only and had bought a hitatchi replacement awhile back in view of replacing.. Then i had faulty nsf height sensor so decided then to do the whole lot in one go.. I did have white dust in in valve block at resevoir and front but bothhave been cleaned.. Now i have the torpedo look with back extended and front on bump stop....(I also changed relax)
So what are diagnostics telling you now?
1st Jun 2018 11:58 am
murchu4
Member Since: 02 Feb 2014
Location: limerick
Posts: 11
Its going in this afternoon to get diagnostics and re calibration if no faults found... Hopefully its just a re cal
1st Jun 2018 12:04 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4658
Yeah you will need to re-calibrate and hopefully all will be well. Good luck
1st Jun 2018 2:24 pm
murchu4
Member Since: 02 Feb 2014
Location: limerick
Posts: 11
An update had at indie this eve and there was a frayed wire on loom to nsf height sensor so he sorted that and done the re cal and were back in business thanks for the input 👍👍
1st Jun 2018 10:05 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4658
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum