Member Since: 22 May 2017
Location: Brisbane
Posts: 3
Air Suspension fault - C1A18-64
Hi All,
For the past few weeks, i have had an intermittent suspension fault C1A18-64. It hasn't progressed in dropping to the bump stops, or going into limp mode and is easily reset able by switching off, locking and unlocking.
Has anyone experienced this and if so, what was the rectification?
cheers
Geoff
24th Apr 2019 12:30 pm
grzesiul
Member Since: 11 May 2008
Location: UK
Posts: 6407
try recalibraing it
24th Apr 2019 1:55 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5053
Re: Air Suspension fault - C1A18-64
geoffmc wrote:
Hi All,
For the past few weeks, i have had an intermittent suspension fault C1A18-64. It hasn't progressed in dropping to the bump stops, or going into limp mode and is easily reset able by switching off, locking and unlocking.
Has anyone experienced this and if so, what was the rectification?
Member Since: 22 May 2017
Location: Brisbane
Posts: 3
HI All,
so i have replaced the rear valve block and serviced the compressor (replaced the desiccant and filters) and the problem still persists, albeit very intermittently now.
Any other ideas?
cheers
Geoff
26th May 2019 11:17 am
Admirable
Member Since: 19 Jul 2015
Location: Fife
Posts: 1039
Have you done the soapy water test on the dryer end cap?
26th May 2019 12:35 pm
dgardel
Member Since: 03 Nov 2009
Location: Greater Venice
Posts: 2025
Re: Air Suspension fault - C1A18-64
PROFSR G wrote:
geoffmc wrote:
Hi All,
For the past few weeks, i have had an intermittent suspension fault C1A18-64. It hasn't progressed in dropping to the bump stops, or going into limp mode and is easily reset able by switching off, locking and unlocking.
Has anyone experienced this and if so, what was the rectification?
cheers
Geoff
Reservoir valve blocked/ stuck/kaput!
from the workshop manual:
C1A18-64
The pressure increases too much quickly when the tank is filled
- Plausibility error signal
Tank valve jammed in position closed (mechanically)
Conduit pipe obstructed / damaged / crushed
Tank tube clogged air /damaged / crushed
Using the diagnostic system approved by the manufacturer,
test the operation of the tank valve (interface of the vehicle's ride height)
Check for presence of obstructions / damages / crushing of the hose conducted
Check for presence of obstructions / damages / crushing of the hose air tankDiscovery 5 tdv6 HSE Corris Gray Outback Engineering Limited Edition IID Pro MV License
27th May 2019 7:47 am
dgardel
Member Since: 03 Nov 2009
Location: Greater Venice
Posts: 2025
geoffmc wrote:
HI All,
so i have replaced the rear valve block and serviced the compressor (replaced the desiccant and filters) and the problem still persists, albeit very intermittently now.
Any other ideas?
cheers
Geoff
tank (it is the cylinder under the front right door,) valve and/or line, not the front or rear valve block. the valve it's inside the compressor cover.Discovery 5 tdv6 HSE Corris Gray Outback Engineering Limited Edition IID Pro MV License
27th May 2019 7:51 am
geoffmc
Member Since: 22 May 2017
Location: Brisbane
Posts: 3
Hi Guys,
Thanks for the suggestions, looks like i have a bit of work to do this weekend. Ill update on Monday.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
