agree ... saw mine there when I had the centre console apart.
from plenty of posts on here, you have to pull it like you want to break it..
Dean
====================================
2011 D4 XS - OBD port protection, RLD spare wheel protector, All LED interiors lights, Timed Climate enabled, iiD tool paired.
2011 D4 Landmark - Stolen from same dealer before I paid for it
2011 D4 GS - Stolen whilst at dealer ... All LED interiors lights, DRLs, Spare Wheel protector.
1996 300Tdi - Eaten by tin worms
28th Apr 2021 3:31 pm
F355GTS
Member Since: 10 Nov 2008
Location: North Hampshire
Posts: 849
thanks all Mark
28th Apr 2021 4:33 pm
Pedros
Member Since: 25 Jun 2011
Location: Cumbria
Posts: 454
You definitely need to pull it hard! Probably harder than you can do with your hands alone without causing a mishap with your fingers through the loop. Thread a spanner or something through to use as a handle.
28th Apr 2021 7:05 pm
galwaygreen
Member Since: 30 Oct 2011
Location: plymouth
Posts: 6525
pull hard very hard with a big stick or tube if needed
28th Apr 2021 10:46 pm
Nobbygezza
Member Since: 19 Apr 2018
Location: Hertfordshire
Posts: 10
Epb
Mine has just done the same, loud screech and warning light on dash. I have removed cup holder and can see cable, I was expecting it to be stiff but you can pull it with no resistance for about 3” I have tried pulling it more but nothing it’s solid, there is a red plastic clip with strap attached just sitting there, also I have a black lever with a picture of foot brake on which is locked shut by a coin type key lock. I have unlocked this a pulled that lever to but still nothing. Please see attached pictures, if anyone can shed some light on where the red clip go’s and how to release handbrake would be great thanks.
16th May 2021 2:55 pm
Landylad
Member Since: 23 Dec 2008
Location: Aberdeenshire
Posts: 366
This loud 'screeching' noise.... just happened to me and parking brake error. What is the cause and fix?
Hopefully manage to get the emergency release sorted, but is that just a one time hit - ie, if I release it, will brakes try and close up again and result in me being back to square one if I drive it?If in doot, flat oot!!
8th Jan 2024 12:32 pm
Landylad
Member Since: 23 Dec 2008
Location: Aberdeenshire
Posts: 366
Re: Epb
Nobbygezza wrote:
Mine has just done the same, loud screech and warning light on dash. I have removed cup holder and can see cable, I was expecting it to be stiff but you can pull it with no resistance for about 3” I have tried pulling it more but nothing it’s solid, there is a red plastic clip with strap attached just sitting there, also I have a black lever with a picture of foot brake on which is locked shut by a coin type key lock. I have unlocked this a pulled that lever to but still nothing. Please see attached pictures, if anyone can shed some light on where the red clip go’s and how to release handbrake would be great thanks.
OK, struggling a wee bit.... I can't see the cable for the emergency release (as picture above with the white plastic shrowd) - could it have been pulled out by a previous (similar) issue? HELP!!!If in doot, flat oot!!
8th Jan 2024 1:36 pm
markate
Member Since: 17 Sep 2011
Location: England
Posts: 704
The wire with the loop on the end is the handbrake release. As others said it needs to be pulled really hard to release.
The red lever is the gearbox release usually used to recover the vehicle if it develops a gearbox fault.
8th Jan 2024 2:45 pm
Landylad
Member Since: 23 Dec 2008
Location: Aberdeenshire
Posts: 366
Yeah, that bit I understand. It's the white loopy wire that's not there. I can just about make out a white plastic grommet at the very bottom of the plastic section - I think that may be it and the actuator has pulled the damn thing almost right back into the subsection of the vehicle.If in doot, flat oot!!
8th Jan 2024 3:10 pm
Admirable
Member Since: 19 Jul 2015
Location: Fife
Posts: 1037
The cable is not white, you're looking for a cable similar to the thin (inner) brake cable you find on a push bike.
8th Jan 2024 3:52 pm
Landylad
Member Since: 23 Dec 2008
Location: Aberdeenshire
Posts: 366
Thanks guys - I'm not Landrover qualified, but I know what a cable looks like
So as it transpired, the cable (with white shroud) had been pulled down underneath where it's typical housed. A bit of persuasion with a spring puller and pair of mole grips and it came back.
Unfortunately, even applying a fair old degree of brute force to release, it's not having the desired effect on the drum. I know you guys said it needs LOTS of force, but not entirely sure how much is within practical terms before it would break something.
So all in all, I have a car sat with a seized on left rear drum (EPB) and no ability to move it.
I'm thinking two options here that I saw on YouTube - take the hub off and dismantle shoes - but I don't think this would work as I can't get enough slack in the cable.
Or chop the cable with a grinder/wire cutters before it comes into the break housing?
Either way, I need to get it released so I can drive it to a local garage to get them to look at it.
Actuator or cable problem itself? The actuator still squealing - I removed fuse to stop it trying to pull cable any more.
Arrrrrgh!If in doot, flat oot!!
8th Jan 2024 4:10 pm
KPTV8
Member Since: 05 Feb 2012
Location: Itinerant !! (Scotland/Donegal)
Posts: 187
Hi, I had exactly same a few months ago, pulled the release cable so hard the crimp failed (where the cable is crimped back on itself to form that loop accessed from behind the gear lever).
Car was not accessible by recovery, so I had to take an angle grinder to one of the cables just forward of rear wheels. Huge BANG when the cable parted.
Be SLIGHTLY careful, due to BIG tension in that cable (not the emergency release cable, I mean the cable from servo to drum), when I finally cut through it, the car settled a little, so you don't want to be too close and be trapped. Also of course, ensure transmission is in "P", or "1" if it's a manual.
Wish you luck ))
8th Jan 2024 4:41 pm
Landylad
Member Since: 23 Dec 2008
Location: Aberdeenshire
Posts: 366
Cheers KPTV8. I spoke with a local mechanic I use. He reckons it could be the shoe lining has slipped, binding up the drum. I don't think me pulling the emergency release any more than I am, is going to prize it loose.
Think the first thing I need to do is try and get the drum off and release the shoes. He said the adjuster could have got ceased up with the frosty conditions. Last resort is cut the cable.
Just need to get it mobile first and foremost.If in doot, flat oot!!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
... All LED interiors lights, DRLs, Spare Wheel protector.
))
