| Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Groups · Profile · Donate ·
Log In
|
- You are currently viewing DISCO4.COM as a guest - Register to take part or Log In
Philw1
Member Since: 31 Jan 2023
Location: boston lincs
Posts: 72
  
|
Hi I have a bit of excess backlash in my rear diff (05 tdv6 auto) none locking ,
my question is does anybody know where I can get the necessary shims for the crown wheel and pinion and new seals of course , there is no noise from the diff whatsoever no whining or rumble ,
just a noticeable clunk ,thump when the backlash is taken up .
I don't know how much excessive backlash is until I get under the truck this weekend with the dial gauge to know what thickness the required shims will be .
Many thanks Phil
|
 10th Feb 2023 10:02 pm |
|
|
Breg90
Member Since: 04 Feb 2017
Location: Falkirk
Posts: 348
|
Check the diff preload - prop off, drive shafts out. Measure torque to turn diff. It will be too slack as the bearings will be worn. Fit new bearings and it will be ‘ok’ Series one 1949 - in bits, chassis is strapped to the ceiling in my garage (beside the canoe)
LR 90 - In bits
Disco 3 - currently in bits
|
| 10th Feb 2023 10:50 pm |
|
|
Breg90
Member Since: 04 Feb 2017
Location: Falkirk
Posts: 348
|
https://www.disco3.co.uk/forum/topic189350-135.html
This covers my rear diff rebuild Series one 1949 - in bits, chassis is strapped to the ceiling in my garage (beside the canoe)
LR 90 - In bits
Disco 3 - currently in bits
|
| 10th Feb 2023 10:53 pm |
|
|
Breg90
Member Since: 04 Feb 2017
Location: Falkirk
Posts: 348
|
But check you rear prop center bearing - might be source of clunk Series one 1949 - in bits, chassis is strapped to the ceiling in my garage (beside the canoe)
LR 90 - In bits
Disco 3 - currently in bits
|
| 10th Feb 2023 10:55 pm |
|
|
Flatlander
Member Since: 20 Jul 2015
Location: Here
Posts: 575
|
...
Last edited by Flatlander on 21st Feb 2023 11:06 pm. Edited 1 time in total
|
| 10th Feb 2023 10:56 pm |
|
|
Philw1
Member Since: 31 Jan 2023
Location: boston lincs
Posts: 72
|
Thank you Breg90 ,that's an enormous help much appreciated , Do you happen to have the bearing numbers for front and rear diff's be nice to have them in hand when old ones removed ,may as well do both of the diffs at the same time ,got a slight hum of the front diff ,
Many thanks Phil
|
| 10th Feb 2023 11:23 pm |
|
|
Philw1
Member Since: 31 Jan 2023
Location: boston lincs
Posts: 72
|
Breg90 , it is a new rear prop and all good there ,
Flatlander , thank you for your input much appreciated ,will ensure the pre-load and back lash are both correct .
|
| 10th Feb 2023 11:30 pm |
|
|
Breg90
Member Since: 04 Feb 2017
Location: Falkirk
Posts: 348
|
Philw1 wrote:Thank you Breg90 ,that's an enormous help much appreciated , Do you happen to have the bearing numbers for front and rear diff's be nice to have them in hand when old ones removed ,may as well do both of the diffs at the same time ,got a slight hum of the front diff ,
Many thanks Phil
Advanced factors do a kit Series one 1949 - in bits, chassis is strapped to the ceiling in my garage (beside the canoe)
LR 90 - In bits
Disco 3 - currently in bits
|
| 11th Feb 2023 12:04 am |
|
|
|
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
|
|
DISCO4.COM is independent and not affiliated to Land Rover.
