Member Since: 15 Jul 2014
Location: cavaillon
Posts: 188
IPCU and ALTOX
HI at all
my IPCU don't run with ALTOX ....i program LPTEMP1 with temp for starting the fan and nothing happen
i'm lost
Mayday
PHILIPPE
21st Feb 2019 12:35 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 188
Hi.... The message of altox...
HEATER OFF
GSM (0-31): 11
Voltage: 11.8V
Heater temp: 20C
Sensor temp: 11C
Flame: no
Output: on
<admin>
21st Feb 2019 6:48 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 188
output is on but the ipcu don't run the fan!!
thank's for your reponse
Philippe
21st Feb 2019 6:55 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 188
nothing??
21st Feb 2019 9:35 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 188
Hi...
When I send this message LTEMP1:80 for example I receive from altox this text
W1 R1 B0 T30,0,0
L0,0,0 F0 P0
K0 S0,1,0
S1:w0,e1,v11.6,t99
C1 P""
N1""
N2""
N3""
B"":10,5:0
22nd Feb 2019 10:06 am
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 188
What do you thing?
Thank's
Philippe
22nd Feb 2019 10:07 am
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 188
Hi... Nobody... I am alone with this problem? 🙃
Philippe
24th Feb 2019 3:48 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 188
Coucou.. I'm alone in babylone 😭!!!
8th Mar 2019 8:29 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 188
Coucou.. I'm alone in babylone 😭!!!
8th Mar 2019 8:29 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14129
Member Since: 21 Oct 2016
Location: kent
Posts: 14129
Also just found this ref the fan
When controlled by the Altox W-bus 5, we recommend setting startup temperature for D3/RRS EASY IPCU between 40-50 Celcius , (this is done by texting LTEPM1:## to your Altox W-bus 5)
to prevent unnecessary usage of battery power, then fans will not kick in before coolant is warm
8th Mar 2019 8:45 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14129
Setting up the fan speed
If winter time, set winter switch on 0, turn ignition on, you will hear the flaps turning to selected position and air comes out, turn ignition off, wait for car to turn off completely (a few minutes)
Look in app for Altox, Locate heater temperature, set “LTEMP1:##” 10 degrees above heater temperature.
If heater temperature in app read 7 degrees, set startup temperature to 17 degrees, text “LTEMP1:17” to your Altox WBUS-5
Then press start on ALTOX APP
Wait til heater reached your set temperature, you will hear a small click and fans will start to blow
Use a small screwdriver to turn fan speed up or down on the potentiometer located behind the small hole
We will recommend you set speed between level between 1 and 2 when using temperature controlled/Delayed startup.
You can always set speed up and down, if you want more fan speed later
When done with testing speed, press off in ALTOX APP
Then set up, the startup time by coolant temperature, we recommend between 40-50 degrees Send “LTEMP1:50” to get a startup at 50 degrees
8th Mar 2019 8:50 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 188
Hi.. Thanks Gstuart... I try to do this action :
. I disconnect the wbus5 GSM modul from ipcu modul and I give 12v to yellow wire and gnd to white wire by a external SOURCE... To see if the fan blow..
I am clueless'😢
Merci ii
8th Mar 2019 10:22 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14129
Hi
Ur very welcome, Fingers crossed it’s helps u,alas I’m not really familiar with the system but just found the links
indeed a good idea to see if the fans works ok on putting an external 12 volt supply , at least then can rule it out
Also read where the fan won’t come on until the coolent is warm
Plse let us know how u get on
8th Mar 2019 11:39 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 188
OK... Croisons les doigts !! 🤞🙃
Je vous tiens au courant !!
Philippe
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
