Advertise on DISCO4.COM
Forum · Gallery · Wiki · Shop · Sponsors
DISCO4.COM > Technical (D3)

Suspension calibration
Post Reply  Down to end
Page 1 of 1
sweetpea54321
 


Member Since: 23 Nov 2015
Location: Bolton
Posts: 220

England 2005 Discovery 3 TDV6 S Manual Zambezi SilverDiscovery 3
Suspension calibration

Head scratcher... I've just had new suspension arms fitted front and rear and just today had it 4 wheel aligned.

Rear is too high in normal ride height so using guided calibration I have taken to 488 rear and 466 front.

However when I try to apply settings I get operation failed error E 0?

Any ideas before I torch the car!

Thanks

SP
 Mods so far:

New wheel winch
Instrument upgrade (clock on dash)
D4 fascia + Garmin nuvi
LED side light, interior etc
New FL2 rear wheel arch seals
Parrot MKi9200 hands free kit 
 
Post #237384923rd Jul 2024 1:11 pm
View user's profile Send private message View poster's gallery Reply with quote
sweetpea54321
 


Member Since: 23 Nov 2015
Location: Bolton
Posts: 220

England 2005 Discovery 3 TDV6 S Manual Zambezi SilverDiscovery 3

Rears are 485 ...
 Mods so far:

New wheel winch
Instrument upgrade (clock on dash)
D4 fascia + Garmin nuvi
LED side light, interior etc
New FL2 rear wheel arch seals
Parrot MKi9200 hands free kit 
 
Post #237385023rd Jul 2024 1:12 pm
View user's profile Send private message View poster's gallery Reply with quote
PROFSR G
 


Member Since: 06 Mar 2017
Location: Lost
Posts: 5044

Ukraine 2009 Discovery 3 TDV6 Commercial XS Auto Stornoway GreyDiscovery 3

Check there aren't any fault codes logged before you start the calibration.
 yµ (idµ - eAµ) ψ=mψ

 
 
Post #237385723rd Jul 2024 2:44 pm
View user's profile Send private message View poster's gallery Reply with quote
sweetpea54321
 


Member Since: 23 Nov 2015
Location: Bolton
Posts: 220

England 2005 Discovery 3 TDV6 S Manual Zambezi SilverDiscovery 3

Already cleared... I've just contacted Patrick at Gap... and suspect fault with one of rear height sensors.. Will update when sorted.

Thanks
 Mods so far:

New wheel winch
Instrument upgrade (clock on dash)
D4 fascia + Garmin nuvi
LED side light, interior etc
New FL2 rear wheel arch seals
Parrot MKi9200 hands free kit 
 
Post #237386023rd Jul 2024 3:01 pm
View user's profile Send private message View poster's gallery Reply with quote
PROFSR G
 


Member Since: 06 Mar 2017
Location: Lost
Posts: 5044

Ukraine 2009 Discovery 3 TDV6 Commercial XS Auto Stornoway GreyDiscovery 3

What was the fault you cleared?
 yµ (idµ - eAµ) ψ=mψ

 
 
Post #237386423rd Jul 2024 3:09 pm
View user's profile Send private message View poster's gallery Reply with quote
sweetpea54321
 


Member Since: 23 Nov 2015
Location: Bolton
Posts: 220

England 2005 Discovery 3 TDV6 S Manual Zambezi SilverDiscovery 3

It was the usual Christmas tree lights following the new suspension arms being fitted... the steering angle sensor would also have caused this due to misalignment.

There are currently no other faults showing and no warning lights.

I've just ordered a new height sensor to see if that is the issue... I suspect it is... fingers crossed.
 Mods so far:

New wheel winch
Instrument upgrade (clock on dash)
D4 fascia + Garmin nuvi
LED side light, interior etc
New FL2 rear wheel arch seals
Parrot MKi9200 hands free kit 
 
Post #237386523rd Jul 2024 3:12 pm
View user's profile Send private message View poster's gallery Reply with quote
PROFSR G
 


Member Since: 06 Mar 2017
Location: Lost
Posts: 5044

Ukraine 2009 Discovery 3 TDV6 Commercial XS Auto Stornoway GreyDiscovery 3

You need the specific fault code that's relative as each corner has different sensor.
 yµ (idµ - eAµ) ψ=mψ

 
 
Post #237386623rd Jul 2024 3:32 pm
View user's profile Send private message View poster's gallery Reply with quote
mick_n3
 


Member Since: 19 May 2017
Location: Kettering
Posts: 428

United Kingdom 2008 Discovery 3 TDV6 HSE Auto Buckingham BlueDiscovery 3
Re: Suspension calibration

sweetpea54321 wrote:
Head scratcher... I've just had new suspension arms fitted front and rear and just today had it 4 wheel aligned.

Rear is too high in normal ride height so using guided calibration I have taken to 488 rear and 466 front.

However when I try to apply settings I get operation failed error E 0?

Any ideas before I torch the car!

Thanks

SP


Had same issue last time I calibrated mine.
Contacted Patrick and sent him a log from iid but nothing out of ordinary


I kept trying and it eventually accepted new settings
 
M6NIO 
 
Post #237386723rd Jul 2024 3:35 pm
View user's profile Send private message View poster's gallery Reply with quote
sweetpea54321
 


Member Since: 23 Nov 2015
Location: Bolton
Posts: 220

England 2005 Discovery 3 TDV6 S Manual Zambezi SilverDiscovery 3

Patrick is on the case... he also mentioned about chance of sensor arm being on backwards? Anyone had this? And how is this possible?
 Mods so far:

New wheel winch
Instrument upgrade (clock on dash)
D4 fascia + Garmin nuvi
LED side light, interior etc
New FL2 rear wheel arch seals
Parrot MKi9200 hands free kit 
 
Post #237387723rd Jul 2024 6:53 pm
View user's profile Send private message View poster's gallery Reply with quote
sweetpea54321
 


Member Since: 23 Nov 2015
Location: Bolton
Posts: 220

England 2005 Discovery 3 TDV6 S Manual Zambezi SilverDiscovery 3

This morning I had another look at the issue and decided to make smaller incremental changes to the ride height using the iid and it has worked faultlessly.


I suspect the changes in rear ride height were too great to complete in one stage and this was causing the error? Not sure... anyway glad to say it's now resolved.

485 rear and 466 front.

Thanks

SP
 Mods so far:

New wheel winch
Instrument upgrade (clock on dash)
D4 fascia + Garmin nuvi
LED side light, interior etc
New FL2 rear wheel arch seals
Parrot MKi9200 hands free kit 
 
Post #237391324th Jul 2024 10:14 am
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO4.COM is independent and not affiliated to Land Rover.
Switch to Mobile Site