I dont have any metric bolts at home and would like to pick some up on the way home from work. Any one have any idea what size bolt goes in this threaded hole? Its behind the back left rear panel. Im looking at bolting a bracket to it.
Sceen name use to be "wantsanlr3"
Club Traxide
Club RLD winch mount
Club MTRs
-MY05 SE
-A frankenstein Mini '66 sportspack with a vauxhall lump
-'64 AH Sprite
not to sure could be 6mm would know if i so it in the flesh as they sayHome of RLD Hidden winch mounts Spare wheel Locks Trailer Body Fabrication [email protected] D3/4 sump plates MY 14 sump plates and the Discovery Sport wheel protectors Discovery 5 wheel locks
more Helsport tents and other things for camping Law of Mechanical Repair:
"After your hands are coated with grease, your nose will begin to itch and you'll have to pee!"
4th Mar 2009 4:38 pm
Alex E Holy Bratwurst!
Member Since: 22 Mar 2006
Location: Club Tropicana (the drink's aren't free)
Posts: 869
168mm I'm Powered by........Diesel
4th Mar 2009 4:40 pm
SJR
Member Since: 09 Aug 2006
Location: East Manchester
Posts: 4030
Alex E wrote:
168mm
Really it doesn't look 16.8cm wide to me I believe that every human has a finite number of heart-beats. I don't intend to waste any of mine running around doing exercises.
Buzz Aldrin (1930 -
4th Mar 2009 4:42 pm
BrumLee
Member Since: 07 Mar 2008
Location: West Midlands
Posts: 1360
If the bolts in the picture have a 10mm head then the thread will be 6mm. Goes funny after that as 13mm head is 8mm thread and 17mm head is 10mm thread Why can't they stick to even numbers
Some of the modern forged hexflange have a smaller head than std hex heads
"I know that you believe that you understood what you think I said, but I am not sure you realize that what you read is not what I meant"
4th Mar 2009 10:43 pm
Bodsy Site Sponsor
Member Since: 06 Nov 2006
Location: In the Clubhouse
Posts: 21361
A standard Hexagonal head (Hex head) fastener is just what is says, it is normaly used with a washer and nut on the other side of a mechanical joint.
A Hex flange is a bolt or set screw (there is a difference) with the a hexagonal head that incorporates a washer/flange into the underhead form, and is used on captive nut / weld nut applications.
With a built in washer the head does not need to be as big.
To put it another way, you always need a washer form under the part you turn, this is where the torque measurements are specified.
the rest is too boring to rabbit on about.
"I know that you believe that you understood what you think I said, but I am not sure you realize that what you read is not what I meant"
If you have the 5 seater, you should have a tool storage area in the boot area. Lift the door and you'll find 6mm cap screws securing the door to the hinge. Take it out to verify the size. I just bought 4 today to repair this very door hinge connection. $3.00USD ea. at the local hardware store. Hope this helps.2006 D3 Tonga Green
275/65/18 GY DuraTracs - ARB w/ EP9.0 - Sasquatch Rods
5th Mar 2009 1:33 am
Alan G
Member Since: 15 Oct 2008
Location: Lanarkshire
Posts: 1372
BrumLee wrote:
If the bolts in the picture have a 10mm head then the thread will be 6mm. Goes funny after that as 13mm head is 8mm thread and 17mm head is 10mm thread Why can't they stick to even numbers
Yes, but haven't you found that sometime the Japanese market can be the exception?
I can remember them using 11mm, 14mm hex heads rather that the 10 & 13mm one's that we're used to. ATB
Member Since: 15 Oct 2008
Location: Lanarkshire
Posts: 1372
RLD wrote:
not to sure could be 6mm would know if i so it in the flesh as they say
Agree with Ray's observations. if you look at the two heads at the LHS of the hole, then they look about a 10mm spanner size, 6mm thread. Why not remove one of those and try in in the thread?ATB
Member Since: 07 Mar 2008
Location: West Midlands
Posts: 1360
Alan G wrote:
I can remember them using 11mm, 14mm hex heads rather that the 10 & 13mm one's that we're used to.
Mercedes and Volvo use 15mm, 18mm and 21mm, all very frustrating
5th Mar 2009 3:51 pm
caverD3
Member Since: 03 Jul 2006
Location: Oberon, NSW
Posts: 6922
You could just use self tapping roofing screws?“There are only three sports: bullfighting, motor racing, and mountaineering; all the rest are merely gamesâ€
Ernest Hemmingway
D4 3.0 Active Diff, Adaptive Lights, High Beam Assist, Surround Cameras, Privacy Glass.
D3 2.7:Adaptive Headlights,Electronic Rear Diff,ARB Bar,Blaupunkt Speakers,JVC Powered Subwoofer,Removable Snorkel,Mitch Hitch,Pioneer After Market Head Unit,Steering Wheel Control Adaptor,Remote Adjustable Supension Rod System, Taxside Dual Battery System.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum