Not sure if anyone is interested but as the D4 Mantec plate differs from the D3 one here's a few pictures.
As it comes:
Click image to enlarge
Sprayed Matt-Black:
Click image to enlarge
As on the D3 remove the central plastic valance which covers the recovery point. then you need to remove the two "spats" this requires a T30 torx driver (1x screw each side) and a philips screwdriver (3x screws each side). Once the spats are removed refit the T30 screws.
The 13mm hexhead bolts at the back are also removed as these are replaced with 15mm hexhead longer ones.
The fitting points are the same as one the D3, and tighted up the 4 bolts to 68Nm and you also then refit one of the philips screws either side to hold the wheelarche liner onto the valance.
Here's it fitted - note it's not a tight fitting to the bumper as the D3 one, there's a noticable gap between the top of the plate and the bumper (I took it off to double check that I hadn't used the wrong mounts, but that appears to be the way the new one fits):
Click image to enlarge
Click image to enlarge
Here's the tools and bits you should expect left over (minus the central valance as I forgot to include it in the picture ):
Click image to enlarge
Last edited by MrH on 12th Feb 2010 3:54 pm. Edited 1 time in total
12th Feb 2010 2:04 pm
tanters
Member Since: 24 Oct 2007
Location: Oireland
Posts: 4287
Its quiet different isn't it Surprising that.
Did you ask Mantex about the gap?A happy childhood ... is the worst possible preparation for life.
Member Since: 29 Nov 2006
Location: North Yorkshire
Posts: 15263
Well that looks a good fit compared to the one Bill Wright tried to fit to his D4.
Think he had to go back to supplier with his ... the gaps were way out....... always on the road less travelled 🚧
I'm hopefully going to get to see some LRE D4's tomorrow at Eastnor so will compare those with mine and report back.
12th Feb 2010 3:53 pm
Bill Wright
Member Since: 03 Nov 2007
Location: Glorious Devon
Posts: 3254
MR H
I've just had mine returned from Mantec after being re-jigged. They got a D4 from LR and tried my guard on it and discovered it was wrong although it matched their patent shape for the D4. When I originally fitted it, it had a 30mm gap at the top and the side contours were way out. The re-jigged plate gap is 20mm on the right side and 15mm on the left side and the contour still looks like cack. I've been in touch and they say that they will send me one of new batch being made next week. If that's no better, they're saying
"if the new guard we send still does not fit the vehicle properly I can only suggest taking the vehicle back to the dealer and checking the body work is fitted correctly, we have had issues in the past"
It's hardly accurate engineering and I am very disappointed. On my D3, the plate fitted flush almost to the base of the bumper.
I'd be interested in your observations sat Eastnor and pictures if possible.
Hope this helps
Pictures in my gallery of the first fitting
Regards
Bill WrightNever take life too seriously. Nobody gets out alive anyway.
I've just contacted Mantec and asked for their feedback. I'll keep you posted.
12th Feb 2010 5:20 pm
DiscoDunc
Member Since: 08 May 2006
Location: Bristol
Posts: 16390
its looking a bit toooooo clean under there MrH Duncan
-----------------------------------------------------
If I'd known I was going to be so thirsty this morning I'd have drunk more beer last night.
FFRR Autobiography 4.4 SDV8 MY17
D4 HSE MY13 SOLD
FFRR 3.6 Vogue TDV8 SOLD
D4 HSE MY10 SOLD
D4 SE TECH MY15 SOLD
D4 XS MY12 SOLD
D4 HSE MY10 SOLD
D3 HSE MY06 - Re-Cycled Worldwide
Ok Guys, back on topic. As promosed I've been to LRE Eastnor today and the friend folks there let me have a really good snoop around one of their D4's - Many thanks Dave
The four D4s I looked at all had nice, closely fitting Mantec plates - yes there was a minor gap, but no more that 3-5mm. Another thing you'll notice on the pictures is that the plates have the two cuts welded back up to form a solid plate.
Click image to enlarge
Click image to enlarge
Now just awaiting for Mantec's response next week - will keep you posted.
13th Feb 2010 3:24 pm
grzesiul
Member Since: 11 May 2008
Location: UK
Posts: 6400
looks as if u et your new toy armored huh?
13th Feb 2010 3:30 pm
Bill Wright
Member Since: 03 Nov 2007
Location: Glorious Devon
Posts: 3254
That's a much better fit and I'd be happier with that. At least the front edge follows the upward slant of the bumper at the ends. Let's see what MANTEC send me when they make the next new batch. The cuts/splits on mine are welded on the top of the guard but only for about 30mm of their length.
Bill WrightNever take life too seriously. Nobody gets out alive anyway.
D4 SDV6 SE Tech Kaikoura Stone MY15.
13th Feb 2010 5:18 pm
Bill Wright
Member Since: 03 Nov 2007
Location: Glorious Devon
Posts: 3254
Just got a new Sump Guard from Mantec. It's marginally better in that the 20mm gap is now 12mm and the 12mm gap is now 5mm but the fit is not as good as those LRE vehilces in earlier photos.
What to do eh? I'm getting jazzed off with the tooing and froing. I guess that it'll do the job that it was intended to do and I'll have to live with it. Not a good advert for Mantec though.
Bill WrightNever take life too seriously. Nobody gets out alive anyway.
D4 SDV6 SE Tech Kaikoura Stone MY15.
17th Feb 2010 3:11 pm
ronp
Member Since: 29 Nov 2006
Location: North Yorkshire
Posts: 15263
Has Uncle Ray not got one yet ?...... always on the road less travelled 🚧
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
):
Surprising that.
