Member Since: 11 Jan 2005
Location: Warwickshire, United Kingdom
Posts: 190
The new Driver Information System Handbook (on the GTR website) states that gear selected information is as follows;
(copied from the manual - hope LR dont mind)
The display also indicates the current transmission selection. For example, if reverse gear is selected, then ‘R’ is displayed on the gearbox data icon.
Note: For vehicles with manual transmission, the display will show R N 1 2 3 4 5 6.
For vehicles with automatic transmission, the display will show P R D N
Could be!! - another explanation could be that GTR has been updated to conform with the omission? Indeed LR CS have now admitted that it "has been omitted frm the vehicle" - note "omitted" not "was not intended to be there"
25th Feb 2005 1:11 pm
Wex
Member Since: 16 Apr 2007
Location: Knackeragua
Posts: 5173
Had the same problem with mine after a software update , twice actually. At the same time a warning/fault appeared for the park brakeThe service rep I spoke to says it has happened to a few vehicles sold from his dealership but managed to fix mine and to date no probs.
20th Apr 2007 9:42 am
Geoff S
Member Since: 26 Feb 2008
Location: Ormskirk
Posts: 1
GEAR NOT SHOWING
I had this fault with mine and the warning message 'Park Brake Fault' I had the Land Rover Assist guy out who fixed the problem, it was a computer software issue where the memory had 'lost' the gear settings. I had to re-train the memory to recognise the gears by driving for 10 seconds in each gear inc reverse. (A useful tip was to do it in low ratio on a quite road) Worked a treat, he plugged in his laptop and diagnosed the fault. Cleared it from memory and touch wood has not reoccurred.
Clever these computers Geoff S
26th Feb 2008 10:18 pm
Wex
Member Since: 16 Apr 2007
Location: Knackeragua
Posts: 5173
Mine went at least a couple of times after my post above.I used the " gear retrain" method many times but it only solved it temporarily.Replaced gear sensor module and a transfer case module and so far so good.
26th Feb 2008 10:24 pm
robsmith
Member Since: 02 Sep 2007
Location: Staffordshire
Posts: 2401
Sounds very like the problems I've ben having as well.
Just spoken to the dealer for the umpteenth time and finally got through to someone with greasy hands who was getting a bit frustrated with mine. He said - "Yours is the one that comes in with an EPB fault indication, then loss of gear indication and reversing lights isn't it?". After the mechanic had "sorted it" on the last visit he "took it for a blast" and thinks to himself "This clutch feels wrong", so has a prod and poke to see what's what. The self adjuster has become a self non-adjuster, so needs to be looked at. I understand he's ordered all the bits he can (more than he expects to use) so they can get it all on out and do it all rather than have me keep on coming back every few weeks.....Rob Smith
Silver rools OK
14th Apr 2008 4:51 pm
Discolaw
Member Since: 02 Dec 2006
Location: Burnley
Posts: 88
My Manual Disco3 suffered the following faults, all on one day
will not release parking brake automatically
reverse sensors stopped bleeping
gear selected screen blank for first and reverse, about 4 seconds delay on the others
Coincidence?
I am guessing its a software/electronics fault
will call dealer and report back
If of course anyone has any thoughts or similar experiences....
Duncan
14th Sep 2008 4:35 pm
Gareth Site Moderator
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 26774
There is a post about this somewhere. Its easy to fix.
I think you need to find a quiet stretch of road, engage low box. Start in first and drive through each gear in turn,1,2,3,4,5,6, holding it in each gear until the gear number displays.
I think thats it, mine is auto so never had the issue.
14th Sep 2008 4:38 pm
DiscoStu
Member Since: 09 Apr 2006
Location: London
Posts: 11412
Member Since: 09 Jun 2005
Location: Ubique
Posts: 16534
Start in reverse then each forward gear, hold each gear with foot fully off the clutch until the gear indication shows the selected gear, this must all be done in one ignition cycle. Once complete turn ignition off and remove key until the radio clock & park brake indicator go off.
14th Sep 2008 4:41 pm
Discolaw
Member Since: 02 Dec 2006
Location: Burnley
Posts: 88
That worked!
thanks for the advice
now have gear indicator back and parking sensors, and reversing lights
still no auto release EPB, not an issue, except for the warning light on the display
14th Sep 2008 10:53 pm
Bobby N
Member Since: 22 Sep 2008
Location: Angus
Posts: 2
Re: GEAR NOT SHOWING
suffered symptoms of no gear indicator, park brake fault, no reverse lights and sensors - ran through the gear sequence as described - all ok. many thanksChaybikes
22nd Sep 2008 7:24 pm
Discolaw
Member Since: 02 Dec 2006
Location: Burnley
Posts: 88
should have said, that the EPB auto release also returned
Thanks for the advice
22nd Sep 2008 10:02 pm
LRA TECH
Member Since: 23 Oct 2008
Location: West Yorshire
Posts: 29
Gear selected not showing & Auto relaese on manual disco
The first issue is the calibration of the "x-y" gear position switch situated onto of the gearbox,,it's come out of sequence thats all.Symtoms drving along you change gear and then amber park/brake is on and no gear display.H/Brake does still work, if you cycle ignition everything comes back to normal, set off again when you select third3 gear bang it happens again, not a common fault, as we carry full LR IDS diagnosics we can calibrate on site.This involves driving the car through all the gears inc Reverse,,making sure the clutch pedal is fully depressed after each gear change...Doing it this way you the system resets and clears all faults codes...
The auto handbrake relaese on manual disco3 not 100% when it was standard, but am driving a 08reg now,but it was on my last assist vehicle which was a 56reg...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
