Member Since: 06 Apr 2020
Location: Hampshire
Posts: 3
Trip Computer - How to toggle between Trip A, B and Auto
Hi, just got my Disco4 HSE 2011 and can't figure out how to toggle between Trips A, B and Auto. Not sure if I have an issue. It is currently stuck in Auto Trip.
Good question! All I have been able to do in the past while trying that was to loose trip information - not that there is much of it to loose at present.
Reminds me to go charge the battery before I loose ALL information.A vaccine does not stop you catching a virus, or passing it on, or getting ill from it, really ill. It does reduce the likelyhood of you dying when really, really ill. Stay Alive - KEEP AWAY FROM PEOPLE.
NJSSAm I Gammon or Woke ? - I neither know nor care.
2016 Discovery 4 Landmark
2011 Mercedes Benz SL350 (R230)
1973 MG B GT V8 - 3.9L John Eales engine, 5 speed R380 gearbox, since 1975.
1959 MGA roadster - 1.9L Peter Burgess Engine - 5 speed gearbox
Past LRs - Multiple FFRs, Discos & a Series I - some petrol, some diesel,
none Electric or H2 fuel cell - yet.
There are 10 types of people in this world: Those who understand binary, and those who don’t.
6th Apr 2020 10:16 am
andysow
Member Since: 06 Apr 2020
Location: Hampshire
Posts: 3
Use the menu button on the right hand side of the steering wheel. From there it should be quiet self explanatory, but if not I can pop out and check on mine.
Regards,
Steve
6th Apr 2020 10:42 am
dgardel
Member Since: 03 Nov 2009
Location: Greater Venice
Posts: 2025
From the Owner Manual (but never personally tried):
TRIP COMPUTER
The computer memory stores data for a journey,
or a series of journeys, until it is reset to zero.
The displayed information is for guidance only,
as it can be affected by traffic, road, and weather
conditions.
There are 3 trip memories available, A, B and
Auto. You can specify which trip memory is
viewable using the Instrument panel menu.
USING THE TRIP COMPUTER
A short press (1 second or less), or a series of
short presses of the i button (arrowed), will
change the Trip computer display.
The options available are:
• Odometer.
• Trip distance.
• Trip average speed.
• Trip average fuel consumption.
• Instantaneous (short term average) fuel consumption.
• Range available from remaining fuel.
• Blank display.
To reset the Trip computer values to zero, press
and hold the i button for 2 seconds.
To reset the fuel consumption value, press and
hold the i button until the display clears.
There are 3 trip memories available, A, B and
Auto. You can specify which trip memory is
viewable using the i button.
The distance, average speed, and average fuel
economy values for trip A and trip B can be
reset. Set the Trip computer display to show
the trip that you wish to reset, then press and
hold the i button until the message Resetting
trip is displayed.
It is not possible to manually reset the Auto trip
memory. This resets automatically each time
the ignition is switched on.
Trips may be added together, to record a
continuous journey, or removed. Press the i
button for longer than 1 second, when Auto trip
memory values for distance, average speed,
and average fuel economy are displayed, then
Adding last journey or Removing last journey
will appear on the screen. Press the i button for
longer than 1 second, and the previous trip
information will be added to or removed from
the current trip and the new total will be
displayed. There is no limit to the number of
times this canDiscovery 5 tdv6 HSE Corris Gray Outback Engineering Limited Edition IID Pro MV License
6th Apr 2020 12:01 pm
andysow
Member Since: 06 Apr 2020
Location: Hampshire
Posts: 3
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
