| Last additions - D44 Discreet winch mount install |
discrete winch mount407 viewsThe D44 winch mount on the trails. Like it on Facebook https://www.facebook.com/DifferentialPartsUS15 May 2015
|
|
Winch Power upgrade306 viewsUsing 2 warn kits, and removing one of the wires to use on another project. The purpose was to replace the power and ground wire. I used Warn kits, which are 4/0 Welding cable. The original red #4 warped from getting a little too worn. The 2nd
Battery #1 Deka 9A94 AGM Intimidator, Battery #2 Deka 9A47 AGM Intimidator WARN 36080 28" Quick Connect Cable X 2, WARN 26405 Quick Connect Cable 7' X 2, WARN 15901 Black Cable X 1 -- winch control 72" X 1 https://www.facebook.com/DifferentialPartsUS16 Apr 2015
|
|
305 views24 May 2014
|
|
274 views24 May 2014
|
|
542 views10 Jul 2013
|
|
D44 Winch stainless fairlead487 viewsTop view showing the neat and tidy fit and finish, no knee bumpers here.03 Feb 2012
|
|
D44 Winch stainless fairlead654 viewsThe completed D44 winch installation, including the stainless fairlead. A stainless trim plate, and NA license plate holder is on the way.02 Feb 2012
|
|
radar detector wires tucked up high424 viewsThe orange ties hold wiring sockets for floodlights (to be installed). Red tie holds excess wire for radar detector.28 Dec 2011
|
|
radar detector wires tucked up high410 viewsWires tied up neatly away from the electric motor, spool and gearbox.28 Dec 2011
|
|
wires tied up tight539 viewsThe Orange ties hold wiring sockets for floodlights (to be installed). Red tie holds excess wire for radar detector.28 Dec 2011
|
|
winch as viewed through grill490 viewsnote screwdriver laying behind winch. Winch view fitted with bumper and grill in place.28 Dec 2011
|
|
inside bumper view of lever473 viewsView into the bumper of the free spool lever.28 Dec 2011
|
|
close up of 1 1/4" access hole486 viewsView of the 1.25" inch access hole. You can reach your finger or a screwdriver in this hole to move the lever up or down. It will be fitted with a rubber plug when not in use (and when found).28 Dec 2011
|
|
cross view showing access hole500 viewsCross view of the 1.25" inch access hole. You can reach your finger or a screwdriver in this hole to move the lever up or down. It will be fitted with a rubber plug when not in use (and when found)28 Dec 2011
|
|
1 1/4" access hole for lever451 viewsAction view of the 1.25" inch access hole. You can reach your finger or a screwdriver in this hole to move the lever up or down. It will be fitted with a rubber plug when not in use (and when found)28 Dec 2011
|
|
warn winch controller installation607 viewsremotely installed due to space limitations, and to keep the unit dry. Left Hand Drive, fitted in engine bay near washer fluid fill for reference point.27 Dec 2011
|
|
warn winch controller installation541 viewsremotely installed due to space limitations, and to keep the unit dry. Left Hand Drive, fitted in engine bay near washer fluid fill for reference point.27 Dec 2011
|
|
warn winch controller installation566 viewsLeft Hand Drive, fitted in engine bay near washer fluid fill for reference point.Remote control unit fitted on the box. Remotely installed due to space limitations, and to keep the unit dry.
https://www.facebook.com/DifferentialPartsUS27 Dec 2011
|
|
new inner bumper fitted with winch752 viewsD44 Discrete winch mount inner bumper fitted with Warn XD9000 winch. https://www.facebook.com/DifferentialPartsUS27 Dec 2011
|
|
new inner bumper fitted with winch713 viewsD44 Discrete winch mount inner bumper fitted with Warn XD9000 winch.27 Dec 2011
|
|
|
|
