| Search results - "Stainless" |
The full complement of bits and pieces, major parts back from the powder coaters, all bolts nuts washers replaced with stainless steel241 views
|
|
On Solar245 viewsOn Solar, Snomaster Fridge, Ham Radio and 100W Grape Solar panel, Deka 9A94R Intimidator AGM. I can supply the Stainless Snowmaster Fridges. Other components if you need help.
|
|
EGR Blanking215 viewsBlanking plates cut from stainless steel plate.
|
|
Stainless rear sill covers375 views
|
|
EGR Blanking206 viewsBlanking plates cut from stainless steel plate.
|
|
244 viewsStainless steel sill protector plates. Comes as a set of four.
|
|
Stainless Steel Radio & Heater Control Covers110 views
|
|
after market winch mount available in carbon steel or stainless177 views
|
|
Stainless front sill covers381 views
|
|
Stainless Steel Accessory Instructions357 views
|
|
New stainless mid box540 views
|
|
Frontrunner Sump Guard Fitted12 viewsSGLD009
https://www.frontrunneroutfitters.com/en/be/protection-equipment/under-vehicle-protection/land-rover-discovery-2014-present-sump-guard-4-5mm-3cr12-stainless-steel-front-runner.html
|
|
UHF Antenna Mount384 viewsView from underside of bonnet. The lower half of the mount is folded from stainless steel and bolted through an exisitng oval shaped hole in the bonnet. This hole is throught the heavy steel plate that the bonnet hinges bolt to - not just the aluminium panel. A specially machined rectangular nut was made to pass through the oval hole, rotate 90 degrees and then stopped from turning by a slight shoulder on the nut.
|
|
Fixing method14 viewsStainless Jubilee clip to mount electrics box to winch post
|
|
Lug Nut part number RRD500290 outline sketch544 viewsThis single sheet pdf provides dimensions of the LR part number RRD500290 lug nut on vehicles from MY 2005 to 2008, (up to VIN 8A450459). From VIN 8A450460, the part number is RRD500590.
Visually, there is no apparent difference between the two part numbers. The dimensions appear identical as well. The shape, size, and profile of the Stainless Steel "hat" appears identical.
There are I presume differences in metallurgy to reduce corrosion and swelling of the hat or perhaps better sealing between the inside surface of the hat and the steel of the lug nut body. The reality is the differences are not immediately obvious however.
A 22 mm six point half inch or larger socket drive fits over the lug nuts. I use a nominal 36" long breaker bar with the 22mm socket - any shorter bar, best you be in shape. Depending upon your source, for both alloy and steel wheels, the lug nut torque value appears to be 103 lbf ft, (140 Nm); others suggest first tighten to 96 and then finish at 110 lbf ft, (130 and 150 Nm).
|
|
D44 Winch stainless fairlead660 viewsThe completed D44 winch installation, including the stainless fairlead. A stainless trim plate, and NA license plate holder is on the way.
|
|
D44 Winch stainless fairlead492 viewsTop view showing the neat and tidy fit and finish, no knee bumpers here.
|
|
Pioneer TS-SW1041D 10" sub installed123 viewsAfter cutting off the factory sub mount studs, it took ages to bash the indents. To gain more space behind the driver - I changed the driver\'s side license plate from plastic push in lug - to stainless bolt with nyloc nut. Cr@ppy paint job in wrinkle-finish - all I had on hand at the time. Sealed and treated lower tailgate with Dynamat.
|
|
Kit of Stainless Mudflap screws21 views
|
|
Stainless Travel Mug69 views
|
|
Spare whel protector off the car37 viewsMade this one up myself from 2mm Stainless steel plate.
|
|
Wheel protector fitted40 viewsFitted on the car
Made this one up myself from 2mm Stainless steel plate.
|
|
|
|
|
|
