DISCO3.CO.UK Photo Gallery




	Forum · Gallery · Wiki · Shop · Sponsors

Home
·
Login
·

Search results - "Washer"

The full complement of bits and pieces, major parts back from the powder coaters, all bolts nuts washers replaced with stainless steel240 views

51 viewsD44 front winch bumper. Ali washer bottle. D44 rear h/d bumper. centre diff lock. 235x85x16 pirelli muds. OME +2" springs & shocks. front diff guard. side tree bars. wired for roof CB. Aux fuse block. safari snorkel. extended wading tubes. the list goes on...

Fog Light & Washer Jet Install90 views

Mitsubishi Montero Headlight Washer41 views

114 viewsboth adapter the larger one needed a bit chopped off the botom and the washers to fit

180 viewscame loose when washing car with power washer - its 15" long and hollow

Washer Bottle Bracket874 views

New front bumper with headlamp washers, fogs and PDC complete110 views

Headlight washer plugs82 views

bottle with H/L washer pump and leveling sensor to the right - the space on the far right is for the w/screen pump85 views

Headlight washer hose85 views

Wipers, Front and Rear, plus Washers description and operation.809 viewsThis 17 page pdf describes how the wipers, front and rear, plus the washers are intended to operate. Also described is how the rain sensor is designed to function along with a table of the wiper delay timing parameters.

Aux Battery showing ground cable bolt "upside" down 1569 viewsIn order to obtain sufficient height clearance to get the plastic cover back on, I had to install the ground cable to the underside of the battery post connector.

Note the battery vent hose, (approx 5 ft required) is run down into where the windshield washer fluid container is located. There is not much electrical or metal in that area to be corroded by battery gas plus the open end of the vent hose tends to be protected from dirt and stays clean as well.

BCI Group 40R Deka 640RMF battery showing vent hose run forward to windshield washer reservoir area 1425 viewsRecessed post "Euro profile" battery to "match" OEM and stock Land Rover bracket; note that the Traxide SC80-LR module is mounted at an angle to allow for the main cable to sit under the cover so cover still closes.
The battery is a nominal 7", (180mm), high, but sits on a 1" battery spacer set under to raise the bottom front end of the battery such that the approx 11", (290 mm), length of the BCI 40R battery rises above the angled plastic nibs at the forward end bottom of the case front; hence sufficient space, (1/4", 5mm) remains at the brake reservoir end.

Also the 40R battery does not have hold down "flanges" on each end; on the sides yes, but not the ends so no additional length is required.

When I had to replace the 40R, this time I installed the shorter, (9.625"), taller, (7.5") Interstate BCI 47 / DIN H5 battery which eliminated the spacer on the bottom and better fit the stock LR tie down bolt lengths. Deka also has a BCI 47 / DIN H5 that would work fine as well.

64 views

Thread upload1 viewsImage uploaded in thread 198799

52 views

D3 Wipers and Washers22 views

Thread upload1 viewsImage uploaded in thread 149337

Different Llams knob c/w large washer99 views

Thread upload2 viewsImage uploaded in thread 159579

Heated Washer Jets Offside24 views

Heated Washer Jets Nearside25 views

Front bumper view of semi-installed winch119 viewsNote the left-side (looking forward) bracket holding the white windscreen washer bottle.

431 viewsWasher bottle guard, I covered the exposed headlight waser hose with protective tubing.

Warn Winch gromet/retainer for Warn Winch screws197 viewsPart no. for warn winch grommet/washer for warn number plate holder

408 viewsID of washer fuse and fuse "pincer" tool

Retro fitted Headlamp Washer Relay Rewiring Circuit Diagram301 views

25 views

22 views

6 views

screw and washer23 views

1678 viewsBracket that holds the washer bottel in now that the bumper has gone.

20 views

View of mounted panel from front left corner734 viewsI drilled a hole for the supplied 6 mm tie down toggle bolt in a flat portion of the wing on which the panel sits. I inserted a 50 mm flat rubber washer between the wing metal surface and the underside of the black painted panel plate; also a 40 mm flat rubber washer between the supplied fender washer and the metal plate - just seemed like a good idea so surfaces mate well even if wing metal not completely flat.

Mirror shell replaced - notice self tapping screws52 viewsMirror shell replaced - notice self tapping screws to replace "plastic rivet heads" and also washers on inner screw to prevent screw piercing mirror housing due to short hole.

ZF 6HP26 transmission fluid drain and refill procedure4015 viewsThis is the Land Rover instruction pdf and I note they have it right - that is remove the filler plug first, then the drain plug. Also before you attempt that, not only do you need oil, but also new fill and drain plugs as the sealing washers are deemed single use only.

Used Original holes and 3 self tappers extra with penny washers 61 views

New cut out and strength washers glued191 views

warn winch controller installation608 viewsremotely installed due to space limitations, and to keep the unit dry. Left Hand Drive, fitted in engine bay near washer fluid fill for reference point.

warn winch controller installation541 viewsremotely installed due to space limitations, and to keep the unit dry. Left Hand Drive, fitted in engine bay near washer fluid fill for reference point.

warn winch controller installation566 viewsLeft Hand Drive, fitted in engine bay near washer fluid fill for reference point.Remote control unit fitted on the box. Remotely installed due to space limitations, and to keep the unit dry.
https://www.facebook.com/DifferentialPartsUS