| Search results - "rd," |
Calender Entry 2011689 viewsEynsford Ford, Kent.
|
|
Chiave aperta11 viewsUna volta estratto il circuito stampato, facendo leva col cacciavite sulla parte rimasta attaccata ho prelevato la lama della chiave da inserire nel box nuovo.
Once you remove the printed circuit board, leveraging with the screwdriver on the part remained attached, I picked up the blade of the key to be inserted in the new box.
|
|
67 viewsGibb River Rd, Kimberley
|
|
Puncture repair11 viewsI think in total we did this about 10 times, in 6 months, not a bad record, but not easy in the Bush !!
|
|
Disco 3 2007 15 views
|
|
Thread upload7 viewsImage uploaded in new thread
|
|
Thread upload6 viewsImage uploaded in new thread
|
|
Thread upload7 viewsImage uploaded in new thread
|
|
Thread upload7 viewsImage uploaded in new thread
|
|
Thread upload10 viewsImage uploaded in new thread
|
|
Sump guard, note drain holes to rear451 viewsThe sump guard runs back to the crossmember, it\'s a good idea to drill some large - ish drain hiles as there is no way water and mud can escape once it has entered round the revovery point
|
|
Sump guard, side protection over bumper436 views
|
|
Sump guard, upper limit407 views
|
|
I-Pod installed into my Disco 3451 views I-pod video and Geosat2c installed. No visible damage to the deskboard, no holes etc.
|
|
86 viewsLHS rear wheel well, with inner guard off. The rear AC lines (assuming you have an HSE) don\'t run in same way as the RHS, so on all cars, you can fold the red line inboard, with the bend roughly at the blue line, so that the very rare contact with larger tyres is eliminated.
|
|
276 viewsD3 - still going forward, pit 2
|
|
429 viewsWasher bottle guard, I covered the exposed headlight waser hose with protective tubing.
|
|
Entrance to El Questro Station, Gibb River Rd, Kimberley, WA, Australia181 views
|
|
Crossing Drysdale River, Kimberley, WA135 viewsCrossing a river near Drysdale River Rd, Kimberley, WA, Australia
|
|
Queen Victoria\'s Head, Gibb River Rd, Kimberley, WA, Australia155 views
|
|
lr3-kaymar-closed with 20"402 viewsthe kaymar carrier, designed to allow two tires, sets them both a bit outboard, thus blocking the lamp. that\'s when I realized why they put the fully functional lamps in the bumper (functions: running, brakes, signals, hazard)
I plan to re-weld the locating section more towards the middle of the rear similar to Disco II orrientation.
|
|
Regency Stages 2012127 viewsWorking hard, well almost! Radio duty for the Regency Rally at the Bath & West Showground (Shepton Mallet).
|
|
66 views
|
|
Passenger Guard, Wing and Door Damage64 views
|
|
Side Shot664 viewsSliders and plastic wheel arch mud guard, not installed....
|
|
Block Heater and Cord for petrol V8 LR3 North America 120VAC523 viewsThe recommended 120VAC block heater cord is a Temro 3600003. This is a five foot long cord with what is called a Straight connector at the block heater end with holes for two pins; there is also a metal tab located between the two holes serving as the ground conductor. That cord, in addition to having the two pin holes plus ground tab end, is designed for both aluminum and brass heaters as that also matters.
The Land Rover part number for the Block Heater assembly is VUB504640 but is a Temro product not officially marketed by Temro as a Land Rover block heater. The Temro product number is 3100107 which shows as a brass body 30 mm threaded 700 watt 120VAC screw in block heater with a rectangular shaped depression and two pins suitable for the Temro 3600003 cord. Note the word BRASS as it mates with the aluminum OK.
|
|
Voss System 203 Connector cut thru, (similar to in valve block).676 viewsThis is a cut thru of a Voss System 203 connector. The top third of it is similar to the connector that holds the three 6mm plastic tubing lines into each of the front and rear valve blocks.
I say top third, as per the other pictures, the 3 has a Voss assembly that threads into the plastic of the valve block, whereas in the cut thru above, the Voss brass assembly is threading into the brass body of a metric threaded adapter for threading into a standard type metric threaded hole. Note also the two one way sloping ridges of the cutting ring, and the two interal O ring seals that mate with the plastic tubing. There is additionally the small squashed O ring to provide a seal related to the external thread of the Voss cutting ring assembly; (similar to the larger O ring for the brass body external thread).
|
|
|
|
|
