| Search results - "upgrade" |
D3 Brembo Front and Rear Brake Upgrade pg1324 views
|
|
The After - Upgraded Steering Wheel90 views
|
|
D3 Brembo Front and Rear Brake Upgrade pg2324 views
|
|
Traxide USI-160 Install515 viewsOverview picture of Traxide USI-160 upgrade install. This was an upgrade from the SC80 which performed flawlessly. The USI-160 had two relays and can deliver more amperage. As a result, the wiring was upgraded to 4/0 Welding Cable (warn) and heat shielding was added. The unit performs flawlessly to support 2 HAM Radios, Fridge, etc. Like me https://www.facebook.com/DifferentialPartsUS
|
|
Winch Power upgrade319 viewsUsing 2 warn kits, and removing one of the wires to use on another project. The purpose was to replace the power and ground wire. I used Warn kits, which are 4/0 Welding cable. The original red #4 warped from getting a little too worn. The 2nd
Battery #1 Deka 9A94 AGM Intimidator, Battery #2 Deka 9A47 AGM Intimidator WARN 36080 28" Quick Connect Cable X 2, WARN 26405 Quick Connect Cable 7' X 2, WARN 15901 Black Cable X 1 -- winch control 72" X 1 https://www.facebook.com/DifferentialPartsUS
|
|
intercooler hose upgrade job done9 views
|
|
D3 Brembo Front and Rear Brake Upgrade pg3282 views
|
|
4-20200928_Vigor166_Firmware_Upgrade16 views
|
|
D3 Brembo Front and Rear Brake Upgrade pg4329 views
|
|
D3 Brembo Front and Rear Brake Upgrade pg5260 views
|
|
FOR SALE - ONE OFF Land Rover Disco 3 37 viewsOne of a kind Landrover Discovery TDV6 HSE LUX Model 5 door automatic 4x4 diesel evo blue. Upgrades: sidesteps, roof rails, privacy glass, front and rear heated seats/elec seats, landrover tv and headphones, 7 seater black leather, piano black dash/steering wheel, built in fridge, 6 disc changer, sat nav and bluetooth, harman kardon premium entertainment pack, by-xenon adaptive headlights , cruise control and front and rear park distance control, panoramic electric glass roof, 22inch alloy wheels, body kit
|
|
Nav System Error Message20 viewsThis is the error I got onscreen after trying satnav upgrade from a dodgy copy. Same error then using old disc. Solution was to use a 'good' copy or the same type as the duff upgrade disc.
This isn't a duff photo - the screen really does have a double image of the text.
|
|
crankshaft bolt24 viewsBolt on left is new one for upgraded oil pump casing. Bolt on right is what came out. Notice damaged end and shortness of bolt. Inside of crank was inspected wirh borescope and threads etc all ok. New bolt goes in and out ok. Few filings inside but otherwise clear. Not sure why old bolt ended up like that.
|
|
Breather Cap Installed2008 viewsThe black L shaped tube is is the Gore manufactured, (the Gore-Tex people), LR4 Breather Valve installed in an LR3. Naturally the installation looks similar to what one sees on an LR4 or RRS as the Gore breather valve is now OEM for new production.
The part number of this upgraded front differential breather valve is LR019450 and costs about thirty dollars.
|
|
Thread upload17 viewsImage uploaded in thread 115051
|
|
MY12 Discovery 4 Product Brief167 viewsDetails of changes, upgrades etc for MY12
|
|
New Speaker Cables.111 viewsThis is the door connector, Main loom to Right, Door side to the left. to the top of the connectors you can see green and Green white wires which are the speaker ones. The door wiring is premium and has two pairs, the main loom was a 1 pair high line, so i am adding the pair you see (one already pinned up) to upgrade the loom to premium.
|
|
D4 or D3 Upgraded Cup Holder32 views
|
|
Vacuum Pump Upgraded Hose73 views
|
|
Day running lights & led side light upgrade287 views
|
|
EBC V8 Upgrade 181 views
|
|
EBC V8 Upgrade85 views
|
|
Before129 viewsMY05 Instrument cluster + Software upgrade
FBH indicator instead of lights indicator !
|
|
![front-rear-disc-upgrade-kits-to-v8-size-12793-c[ekm]170x140[ekm].jpg](albums/userpics/33392/thumb_front-rear-disc-upgrade-kits-to-v8-size-12793-c%5Bekm%5D170x140%5Bekm%5D.jpg "Filename=front-rear-disc-upgrade-kits-to-v8-size-12793-c[ekm]170x140[ekm].jpg
Filesize=6KB
Dimensions=170x140
Date added=17.Sep 2018")
Thread upload9 viewsImage uploaded in thread 135978
|
|
Philips xtreme vision upgrade 45 views
|
|
Front Grill upgrade Hawke96 views
|
|
Upgraded front disc29 views
|
|
Upgraded caliper carrier front27 views
|
|
Picture of the engine compartment fuse panel5780 viewsEngine compartment fuse panel located near the battery. This is where F3E, (5 amp), F26E, (20 amp), Fuseable link 10E, (60 amp) and Relay 7E, the now upgraded 70 amp air compressor motor relay, part number YWB500220, (E is for Engine compartment fuse box), are all located. Fuse F35P, (5 amp), is inside the Passenger compartment behind the lower glove box door.
To keep the suspension from going down to the stops when driving, (or parked), it appears that it is only really necessary to remove F26E to depower the exhaust valve and generally keep all the valve block solenoid valves in a closed position trapping whatever air is within the air springs. F3E gets its power thru F26E, so when F26E is removed, the F3E circuit is automatically de-powered. F35P is more interesting in that battery power goes thru the ignition switch and F35P and then into the air suspension control unit. Apparently however, if F26E is removed, removing the F35P is not needed even when the engine is running.
With all fuses still in, if you have a problem, in practice, ideally, the compressor still works and will raise the 3 to an appropriate height. If so, one can then shut the engine off and allow the computers to go to sleep and then you remove the fuse(s). In actual practice, it seems that one need only pull the F26E fuse and can do so with the engine running. All the same, one might consider that the 3 is first a mobile computer, and secondly a 4x4. Computers prefer to go to sleep before the plug is pulled on them, however given that F26E circuit is always alive, then the computer never sleeps. With the fuse(s) pulled, and if you are still up, you can now be a 4x4 instead of a low rider. The whole purpose of the fuse pulling exercise is to depower the one and only system exhaust valve that is physically located within the compressor unit, (to keep it from opening), and secondarily to keep closed the four air spring solenoids within the block valves. This also shuts the air compressor down and stops the air compressor from making air even if the compressor is still good. That is why you initially need the fuse(s) in to allow the compressor to make air if it can.
|
|
led upgrade light86 views
|
|
H7 Upgrade ABD vs philips standard main beam only HIDS4U85 views
|
|
led boot space light upgrade96 viewsClose up showing how easy the led ultra bright modules fits into original housing
|
|
upgrade d2s bulb left 6000k vs philips d2s colormatch 5000k hids4u75 viewsHIDS4U 6000K D2S vs Philips Colormatch D2S bulb
|
|
3106 viewsindicators & wheel centres upgraded
|
|
boot led upgrade78 views
|
|
boot light upgrade77 views
|
|
osram d1s d2s cool blue intense upgrade xenon bulb white from hids4u71 views
|
|
philips d2s d1s ultrablue upgrade hid xenon bulbs hids4u62 views
|
|
osram d1s cool blue intense upgrade xenon bulb white from hids4u94 viewsThese cool blue intense are 5000k and a whiter light than philips ultrablue and match the 5000k leds better. they are also the brightest hid bulbs we have tested
|
|
philips d1s ultrablue upgrade hid xenon bulbs hids4u79 viewsThese bulbs have a whiter light than standard and a blue coating gives a blue tint from a distance and at the edge of the light beam when parked against a wall.
|
|
HSE Interior148 viewsBlack Leather interior with upgraded Steering Wheel and Wood Trim
|
|
PARKING_HEATER_UPGRADE_KIT34 viewsHow to upgrade the water piping
|
|
Upgrade manual FBH to parking heater39 viewsManual to upgrade FBH to full parking heater functionality
Translated in English from an official German language factory manual.
|
|
Underhood Fuse and Relay Box drawing 3055 viewsShows the various fuse and relay locations. Fuse 3E, (5 amp), and Fuse 26E, (20 amp), as well as upgraded 70 amp Relay 7, part number YWB500220, locations are displayed. Relay 7 sends battery power to the compressor from the 60 amp fusible link called up as 10E. Fuse 26E is what provides full time always on battery power to the air suspension ECU and hence powers the auto level wakeup when the vehicle is shut down and say parked for the night. Removing F26E is the primary method to disable the air suspension system; Removing F35P is more if you want to experiment with it from inside.
I found it useful when I had a suspension problem, (actually a wheel alignment problem picked up by the steering wheel angle sensor), that only showed itself on the highway but allowed for no trouble light driving in the city. This was because in the city, the steering wheel was always in motion and rarely was the vehicle driven in a near straight line for very much distance.
|
|
car before any upgrades16 views
|
|
207 views
|
|
chinese satnav36 viewsthis screen shows sts (very useful....not) and speed which used to be on main display but after upgrade is not
|
|
Rebuild Kit1032 viewsReplacement custom Crown Wheel & Pinion, upgraded seals, OE bearings, replacement needle bearings.https://www.facebook.com/DifferentialPartsUS
|
|
65 views
|
|
83 views
|
|
Turbo Change21 viewsTurbo hoses were upgraded to silicone jobbies
|
|
Lights42 viewsHID upgrade pictures
|
|
Powerchip Australia - TDV6 Gold Upgrade201 viewsFrom an Aussie company that has advertised in motoring magazines for the last 8-10 years that I can recall. The cost is $AUD1491 (~596GBP). Does anyone know anything about them?
Booklet shows engine chart comparing standard with Powerchip's Gold 'chip'.
|
|
Tow Bar Switch upgrade7 views
|
|
Thread upload27 viewsImage uploaded in thread 92518
|
|
Air Compressor 70 amp replacement relay1393 viewsThere is a software update, 09 April 2010, LTB00270, for the compressor which reduces the shut down pressure to about 205 psig (14 bar). The update is usually done when changing to a new compressor and also includes replacing the R7 relay in the engine compartment fuse box, 07 DEC 2010 LTB00331.
The newer grey case coloured relay, part # YWB500220, shows to be rated at 70 amps, (the relay, not the compressor), however the previous black case coloured relay also indicates 70 amps.
Both the new and replaced relay show on their wiring diagrams to have a parallel voltage spike resistor, (probably 560 ohms), across the coil terminals, #1 and #2. This means one does not just replace the relay with any four prong 70 amp ISO sized relay that one happens upon.
One presumes the grey relay is either upgraded or just being installed for good measure. The relay is common on Ford Fiesta for the seat heater relay, Ford part number 5M5T 14B 192 EA; also Volvo, part number 30765034. The Tyco part number moulded on the grey body is V23136-J4-X62.
|
|
Xenon HID upgrade183 views
|
|
Xenon HID upgrade192 views
|
|
Thread upload33 viewsImage uploaded in new thread
|
|
|
|
|
