Member Since: 03 Nov 2017
Location: Dorset
Posts: 18
Engine Oil Level Monitor System Fault
Quite new to the D4 only had one since November last year MY2015. Looking for a bit of advice, had a warning come up on my D4 about 4 weeks ago saying Engine Oil Level Monitor System Fault. After finishing my journey I turned the engine off and restarted it and the error message had cleared. It hasn’t come on since, when I check the oil level it is always showing full, the last service was 4501 miles ago and the car has done just under 28000 miles. What I am concerned about is whether the Oil monitor is working as I thought the SDV6 3.0l burnt oil and had to be topped up every so often, I don’t want to damage the engine by having a low oil level. Your thoughts would be appreciated.
26th Mar 2018 9:16 pm
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
The fault probably needs attention. As for oil burn mine has never needed a top-up.Land Rover - Turning Drivers into Mechanics Since 1948
Member Since: 03 May 2016
Location: Kent
Posts: 1660
Yep, I do 8-10k miles a year and never been off full on the display. (2016MY registered Jun 2015)
Agree you should get it checked.Gary
-------------------------------------------
Discovery 4 HSE 2016MY
26th Mar 2018 9:59 pm
tonto2
Member Since: 14 Feb 2012
Location: Fife
Posts: 103
It must be something in the oil, mine did the very same on Sunday.
Same age , same mileage.
27th Mar 2018 6:31 am
Firebod999
Member Since: 03 Nov 2017
Location: Dorset
Posts: 18
Thanks guys, spoke to dealership this morning, they didn’t seem to concerned due to the fact it hasn’t happened again since. They seem to think it was just a glitch but said keep an eye on it and if it happens again then book it in.
27th Mar 2018 11:04 am
trevorb1
Member Since: 21 Mar 2015
Location: Nuneaton
Posts: 62
Its a known fault, oil gets into the wiring in the sump and shorts it out, had it on mine, went away for approx 6 months then did it again. If car is under warranty get it sorted, new sensor, wiring and a retention plate. Its a sump off job and best part of 2 days labour so your looking at a bill for best part of £1000.
Do a search on the forum, theres been a couple of threads on this. Tell tale sign of oil in wiring harness is if they take wiring plug off at sump there will be signs of oil inside.
27th Mar 2018 4:41 pm
Firebod999
Member Since: 03 Nov 2017
Location: Dorset
Posts: 18
Thanks Trevor,
My Landrover 3yr warranty ran out on the 15th March, as I only bought the car in Novemeber 2017 it’s on a 2 year Landrover Approved Used Warranty now. Is that likely to cover this as a known fault?
Dale
27th Mar 2018 5:17 pm
SJT
Member Since: 26 Jun 2017
Location: somerset
Posts: 36
I had the very same fault with my 2015 model after only 20k miles.
It was a replacement loom as above and it took a couple of workshop days for them to sort it.
Glad it was covered by the warranty!!Current - 2016 Commercial SE
Gone - 2014 Commercial XS
Gone - 2015 SE Tech
Gone - 2000 Td5
Gone - 1990 V8 3 door - What a machine!
28th Mar 2018 9:46 am
Sheepy
Member Since: 20 Feb 2013
Location: Bedfordshire
Posts: 630
My '10 plate D4 did that when I first had it, was still under original LR warranty at the time and the dealer sorted it out - so should be covered by the extended warranty.
28th Mar 2018 10:32 am
OJ
Member Since: 01 Oct 2017
Location: Loch Leven
Posts: 725
Had the same fault, cleared a few times but eventually comes back, fortunately LR are going to fix it under warranty, oil in the wiring loom, known fault, 2 day job, update includes a modification to the system.
OJ
16th Apr 2018 11:47 am
imaz
Member Since: 14 May 2020
Location: Perth
Posts: 5
I get this message flash on the dash every so often and displays for about 0.5sec, rather annoying more than anything. Clearly it is a false error because I know how many litres of oil is put in and extracted between services.
As you know it’s a costly and labour intensive job to replace a $200 sensor.
Is there a way to disable the engine oil system monitor fault checks/or perhaps the polling intervals in the ccf editor? Surely there must be a flag which can be disabled.Regards
Imaz
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
