Advertise on DISCO4.COM
Forum · Gallery · Wiki · Shop · Sponsors
  Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Groups · Profile · Donate · Register · Log In  
DISCO4.COM > Maintenance & Mods (D3)

tie links
Post Reply  Down to end
Page 1 of 1
ghostrider6630
 


Member Since: 29 Sep 2014
Location: Swaffham. Norfolk
Posts: 144

United Kingdom 2006 Discovery 3 TDV6 SE Auto Tonga GreenDiscovery 3
tie links

Hi guys

So finally getting to change toe links (panhard rods)
Tomorrow and got tracking booked for Monday
My q is the manual says jack up use axle stands and chanfe whilst wheels removed
Is this correct? Wouldn't it make the rod drop or extend thus fitting new one
Awkward
Would ramps not be better and leaving wheels on there is just enough space
to do it.
Abd finally there us a tightening nut on the shaft what's it for
I cant find any info on adjusting it.
Regards  
Post #22771114th Feb 2022 10:53 pm
View user's profile Send private message View poster's gallery Reply with quote
PROFSR G
 


Member Since: 06 Mar 2017
Location: Lost
Posts: 5016

Ukraine 2009 Discovery 3 TDV6 Commercial XS Auto Stornoway GreyDiscovery 3

Wheels off or at least raised will make fitting easier. The important bit is the height setting at the chassis mount side. Basically the gap between the rubber gaiter and the bottom of the chassis mounting should be 12mm ( you can use a drill bit)

Once that baseline setting is done the rear toe alignment can be carried out accurately. The nut on the shaft is the toe adjustment lock nut. Thumbs Up yµ (idµ - eAµ) ψ=mψ

  
Post #22771194th Feb 2022 11:27 pm
View user's profile Send private message View poster's gallery Reply with quote
ghostrider6630
 


Member Since: 29 Sep 2014
Location: Swaffham. Norfolk
Posts: 144

United Kingdom 2006 Discovery 3 TDV6 SE Auto Tonga GreenDiscovery 3

Great reply thanks
So the adjustment locknut,, do I need to be doing that then i mount the link? Then tighten that up against it? I am surprisedit holds in place.
.and a silly q I am sure what's the drill bit
For  
Post #22771265th Feb 2022 12:18 am
View user's profile Send private message View poster's gallery Reply with quote
PROFSR G
 


Member Since: 06 Mar 2017
Location: Lost
Posts: 5016

Ukraine 2009 Discovery 3 TDV6 Commercial XS Auto Stornoway GreyDiscovery 3

You want to "match" the tie rod to the one you are removing as closely as possible. Once the rod is in place the gap beneath the rubber boot on the ball joint (inner side) and the bottom of the chassis frame needs to be set at 12mm. A 12 mm drill bit will assist you in this!

The centre lock nut may need to be open in order for you to adjust it to "match" the tie rod you are removing. Check the bolt head at the wheel side for centre punch marks, a punch mark must be struck every time this bolt is opened. If the total number of punch marks (including this occasion) = or exceeds 4, you must replace the bolt for a new one! Once installed tighten the bolt to 175Nm if it's suitable to reuse. Then tighten the inner ball joint to 133Nm maintaining the 12mm gap beneath the rubber boot and the chassis frame.

Tighten the lock adjustment nut to 130Nm and have the 4 wheel alignment checked. Failure to observe the bolt reuse protocol can result in it snapping during service life.Thumbs Up

Click image to enlarge
 yµ (idµ - eAµ) ψ=mψ

  
Post #22771375th Feb 2022 3:28 am
View user's profile Send private message View poster's gallery Reply with quote
ghostrider6630
 


Member Since: 29 Sep 2014
Location: Swaffham. Norfolk
Posts: 144

United Kingdom 2006 Discovery 3 TDV6 SE Auto Tonga GreenDiscovery 3
many thanks

Great help appreciated all done now and retracked it even feels smoother to run
relatively easy task in the end just had to going one end of on one link  
Post #228280010th Mar 2022 1:50 am
View user's profile Send private message View poster's gallery Reply with quote
PROFSR G
 


Member Since: 06 Mar 2017
Location: Lost
Posts: 5016

Ukraine 2009 Discovery 3 TDV6 Commercial XS Auto Stornoway GreyDiscovery 3

Thumbs Up yµ (idµ - eAµ) ψ=mψ

  
Post #228280110th Mar 2022 1:59 am
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
< Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums
DISCO4.COM is independent and not affiliated to Land Rover.
Switch to Mobile Site