| Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Groups · Profile · Donate ·
Log In
|
- You are currently viewing DISCO4.COM as a guest - Register to take part or Log In
jik22
Member Since: 14 Oct 2007
Location: Perth
Posts: 64
  
|
I'm getting the above after having quite a bit of wiring work done fitting a BT kit, UHF/VHF radio, screen and sat nav. Just wondering where to start looking for what is presumably a disturbed or broken wire that's causing this? Main areas we were into were the dash, LHS kick panel and under the bonnet, plus running power wires from the aux battery to the rear for a fridge. - Jeff K -
Last edited by jik22 on 1st Oct 2008 1:26 pm. Edited 1 time in total
|
 1st Oct 2008 12:55 pm |
|
|
simonsi
Member Since: 14 Oct 2007
Location: Auckland
Posts: 1264
|
jik22 wrote:Main areas we were into were the dash, LHS kick panel and under the bonnet.
Eeek! Thats a lot of wiring. Sorry I can't offer any real help Cheers
Simon
|
| 1st Oct 2008 12:59 pm |
|
|
DiscoDunc
Member Since: 08 May 2006
Location: Bristol
Posts: 16390
  
|
there is a sensor just below the offside bonnet catch. it may need re-seating or replacing. Had mine replaced once but the second time it happended a disconnect and clean sorted the problem. Duncan
-----------------------------------------------------
If I'd known I was going to be so thirsty this morning I'd have drunk more beer last night.
FFRR Autobiography 4.4 SDV8 MY17
D4 HSE MY13 SOLD
FFRR 3.6 Vogue TDV8 SOLD
D4 HSE MY10 SOLD
D4 SE TECH MY15 SOLD
D4 XS MY12 SOLD
D4 HSE MY10 SOLD
D3 HSE MY06 - Re-Cycled Worldwide
|
| 1st Oct 2008 1:00 pm |
|
|
countrywide
Member Since: 16 Sep 2007
Location: UK
Posts: 6019
 
|
Everytime we go off roading and I lift the bonnet this message keeps coming up. The mud gets in the switch under the bonnet as DiscoDunc mentioned and stops it working. You can see a micro switch if you look closely and I had to bend the contact to make it work again.
|
| 1st Oct 2008 1:41 pm |
|
|
jik22
Member Since: 14 Oct 2007
Location: Perth
Posts: 64
|
Thanks both. I'll have a look in the morning - I really wasn't expecting it to be the actual bonnet switch itself as all we did there was open it to get at the aux battery box, but the error was there on the trip home, so it defintely happened while all the work was getting done! I'd assumed they'd caught something while messing around in the footwell or something! Might save me a 2 hours round trip back to the installer if it is that simple though. - Jeff K -
|
| 1st Oct 2008 1:49 pm |
|
|
jik22
Member Since: 14 Oct 2007
Location: Perth
Posts: 64
|
Right, it's definitely the icroswitch, so thans for the tip. However, short of jamming it with a screwdriver nothing I seem to do to it makes it stay that way when I shut the bloody bonnet. Think LR can sort it now I know I didn't cause the problem with the work and it was probably just the fact we opened the bonnet to begin with! - Jeff K -
|
| 2nd Oct 2008 5:09 am |
|
|
Neil Pettersen
Member Since: 23 Nov 2007
Location: Cutting the grass
Posts: 1254
|
Jeff ,
Mine does the same, probably because I leave the bonnet open when I get home(to let heat out fast)
and all the open/close daily use over works the switch.
I wrapped tape around the bonnet metal, to increase diameter and switch contact ....... it worked ok.
|
| 2nd Oct 2008 5:32 am |
|
|
countrywide
Member Since: 16 Sep 2007
Location: UK
Posts: 6019
|
I had to bend the tab on the switch so that it moved further when the bonnet pin came down.
It is not really the right sort of switch to use where there is a lot of dirt etc, I am surprised they used it.
|
| 2nd Oct 2008 6:35 am |
|
|
Gareth
Site Moderator
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 26775
|
Don't mess around trying to fix it. Just pull the connectors off the microswitch and join them together. I have done this on mine after several failed attempts to fix the problem.
I can see if the bonnet is open or not, I dont need another bong to state the obvious 
|
| 2nd Oct 2008 9:11 am |
|
|
garryc
Member Since: 08 May 2007
Location: Adelaide Hills
Posts: 259
|
countrywide wrote:I had to bend the tab on the switch so that it moved further when the bonnet pin came down.
It is not really the right sort of switch to use where there is a lot of dirt etc, I am surprised they used it.
Had this problem recently. The switch is waterproof. I tried bending the curved metal actuator and initially didn't get it right so I unplugged the cable and put a cut off paper clip (U shape bit)in the pins of the plug and taped it up. Later I adjusted the arm correctly and all has been OK since. The latch arm that actuates the switch moves in a clockwise motion and not up and down so you need to take that into account when bending the actuator arm. You can test it by clicking the latch arm into the closed position with 2 screwdrivers instead of closing and opening the bonnet each time. Just remember to pull the bonnet release before you close the bonnet. regards 2013 D4, E-diff, Vision pack
Never propose to a Yak
|
| 2nd Oct 2008 9:53 am |
|
|
|
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
|
|
DISCO4.COM is independent and not affiliated to Land Rover.
