Member Since: 15 Jan 2016
Location: GL
Posts: 10676
it locks it to the hole where the starter motor goes
18th Jul 2017 4:38 pm
Compusmentis
Member Since: 18 Feb 2016
Location: Effingham
Posts: 237
The pin goes through the engine side of the bell-housing (take the starter out to gain access), and then into the flywheel.New gearbox & TC, 3 x front wheel bearings, belts changed, new oil pump, new battery, new rear prop, new front prop, new front diff, front arb refurbed, front cv boot kit, egr blank and BAS software patch, full rear suspension / drivelive rebuild, new front arms, LED trailer light fix, split charge.
Never had a 107, 90 or 127, but have had most of the rest!
18th Jul 2017 8:25 pm
DerrekL
Member Since: 01 Aug 2016
Location: Bathgate
Posts: 34
ah yes of course.. thanks. It wasn't until I hit 'Submit' on my last question that the penny dropped
19th Jul 2017 8:55 am
annette
Member Since: 16 Dec 2017
Location: Tilarán
Posts: 66
DerrekL wrote:
gilesharrison, given DM advice regarding the correct timing hole being the one that has clear flattened sides. Is this the only hole in the flywheel that you can say has this 'flattened sides' feature?
thank you.. that really made my dayFixing LR problems very far from Solihull.
That's why my newest car is a 1999 Disco 2 V8 with 285.000 miles
The problem is the missing documentation, not the LR
8th May 2018 2:37 pm
loanrangie
Member Since: 18 Jun 2017
Location: Melbourne
Posts: 699
gilesharrison wrote:
I think everyone who uses this forum is well aware that everything that is written is not gospel. I agree that it's the OPs choice as to whether or not to act on any advice offered. I am very grateful for the assistance offered and I wouldn't want anyone to avoid assisting for fear of making mistakes.
Anyway, I've been looking at pictures of flexplates. There appear to be lots of different designs.
I've attached a photo which a believe is the same as mine. I've labelled (with letters) the four torque converter bolt holes. There are then a number of other holes labelled with numbers. I think I'm looking at setting the timing pin in either hole 1 or 2.
For reference, the car is a 2005 2.7 TDV6, UK spec, auto.
Doing this now and i see from this pic that hole number 1 is the only one that will line up with the locking tool and the others are too close to the ring gear so must be for balancing.
Read that the hole has 2 flat sides but not according to this or on my flywheel.
1st Sep 2020 6:04 am
DR
Member Since: 24 Aug 2011
Location: Dublin
Posts: 16
D4 timing mess
Hi
Firstly, thank you to everyone on here - you have helped me keep four Discoverys on the road at a much more affordable price point.
Now to my mess ...
I am currently doing my fourth belt replacement but is has not gone according to plan.
Before removing the old timing belt, I inserted the two camshaft pins - the left side (from the driver's seat) seemed to locate correctly, but the right side seemed to be hitting air behind the belt.
I decided to proceed carefully, replaced the belt- as close as I could to the original position, but after rebuild, it would crank but not start - tested two full manual rotations without problem - I figured a timing issue so back to the drawing board.
This time I removed the starter (I had never had to lock the flywheel on previous jobs (2 x LR3 & 1 x LR4)) - when I removed the belt I tried to find the correct locking points for the camshafts. As before, the left seems to have a clear receptacle for the pin, the right not so much - I set it where the pin went deepest - on rebuilt - the manual crank locks - I have tried it three time, most recently having rotated the two camshaft for the final attempt - but no joy.
I clearly have the crankshaft and the cam shafts out of sync at this stage despite following everything I can find online.
is there anyone out there prepared to have a quick chat to help me out - I would be much obliged
I am in Dublin Ireland - thank so muchDisco 4 MY16
Disco3 my07 - gone
7th Mar 2024 6:03 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10676
I can’t talk on the phone. But.
You need to look with a mirror or video phone at the cam locking holes. To see what’s going on
There is a clear hole for the pins. If you get it slightly off, it will just rest on the side of the casting and feel ok.
On one side you need to have a spanner on the cam bolt to push against the spring resistance to get it correct and in the hole.
It must be quite bad/off if your getting a clash on manual cranking
8th Mar 2024 6:34 am
DR
Member Since: 24 Aug 2011
Location: Dublin
Posts: 16
many thanks Pete
I will try that this morning and let you knowDisco 4 MY16
Disco3 my07 - gone
8th Mar 2024 7:08 am
DR
Member Since: 24 Aug 2011
Location: Dublin
Posts: 16
Hi Pete
That worked - I found the correct locators and the belt is on and turning freely, and the pins line up every two rotations of the flywheels
It will take me at least a day to rebuild everything I have pulled apart - but I will post again at that stage - thanks againDisco 4 MY16
Disco3 my07 - gone
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
