you need a nana nana mount Home of RLD Hidden winch mounts Spare wheel Locks Trailer Body Fabrication ray@rld-tech.co.uk D3/4 sump plates MY 14 sump plates and the Discovery Sport wheel protectors Discovery 5 wheel locks
more Helsport tents and other things for camping Law of Mechanical Repair:
"After your hands are coated with grease, your nose will begin to itch and you'll have to pee!"
5th Sep 2008 12:33 pm
MacLeod 313
Member Since: 18 Apr 2008
Location: away
Posts: 10723
Dashmount.co.uk make a very small and strong bracket for the D3, all you need to do is find the mount or just velcro it. Look in my Gallery, I fitted my Parrot handfree kit with one of these, just remove the trim and it srews in with the stereo torque screws.
5th Sep 2008 1:23 pm
Bodsy Site Sponsor
Member Since: 06 Nov 2006
Location: In the Clubhouse
Posts: 21361
JCB, did your dashnount fit OK with no mods?
I bouight one for my iphone & I needed to drill the bottom hole out a bit more to fit over the plastic lug. Most annoying. Also needed a longer screw!!!Bodsys Brake Bible
Clock/ SNOTM /3Flash / 4x4Info /BT Update /Service Reset/Error Codes / Gearbox Reset See It Here
5th Sep 2008 2:28 pm
MacLeod 313
Member Since: 18 Apr 2008
Location: away
Posts: 10723
Nope, cos i fitted mine lower down than yours, I saw yours in the Gallery. Mine is on my Gallery, opted to go low as the Parrot is'nt removable and wanted it lower so the ASBO, cider drinking, find it harder to see.
Funny on Dashmount.co.uk site shows it in your place, but needs the hole made bigger, fit it lower like mine and no mods needed.
By far still a great little bracket, and very strong
M8 easiest solution is get a 5 in 1 FM transmitter/charger/holder which will plug straight into left hand power socket on centre console & will give you connectivity to incar audio and keep the little blighter powered up. I have had one in my D3 for ipod & Iphone for 2 yrs+ and it works a dream,as nano is lighter it should sit well without any hassle.It also has a USB connector & 3mm jack input so other devices can be plugged into it. Best of all it does not cost a packet!!!.
Give it a go - everything to gain,little money to lose(if at all!!!)
5th Sep 2008 4:46 pm
Dom Harvey Lord of the Four Fingers
Member Since: 15 Apr 2005
Location: Dorset
Posts: 7459
Nah I've already bought the full ipod connection kit but wanted the ipod out not stuck away in the glove box 2004 Discovery 3 - gone
2006 Discovery 3 - gone
2008 Discovery 3 GS - gone
2011 Freelander LE Special Edition - gone
2007 Discovery 3 XS - gone
2012 Discovery 4 GS - gone
2019 RangeRover Evoque 2.00 D150 R-Dynamic
Member Since: 14 Aug 2008
Location: Parked Up
Posts: 256
Bodsy wrote:
JCB, did your dashnount fit OK with no mods?
I bouight one for my iphone & I needed to drill the bottom hole out a bit more to fit over the plastic lug. Most annoying. Also needed a longer screw!!!
i installed teh same dash mount (see my gallery) no drilling or longer screw required
does need a little bend to make the H trim fit snug I have enough money to last me the rest of my life.Unless i buy something..
Slimer - yes but it don't want it stuck in the glovebox?
5th Sep 2008 5:37 pm
Bornidle
Member Since: 14 Aug 2008
Location: Parked Up
Posts: 256
you need this then
Click image to enlarge
I have enough money to last me the rest of my life.Unless i buy something..
5th Sep 2008 5:40 pm
Bornidle
Member Since: 14 Aug 2008
Location: Parked Up
Posts: 256
and if its an iphone dont buy the more expensive holder that goes on the dash mount as the itouch one is cheaper and does BOTH iphone and itouch , i think you said ya had a nano .. o well infos here for anyone looking
I made this mount up, it uses the Belkin connector, the i pod one is better I would think. This is stuck with the double sided number plate tape to a piece of ally 75mm x 20mm painted black (the hole was for a previous mount), it is screw into the plastic but cannot be seen as it's hidden behind the pen tray.
The Nano is only held on the the connector, but rest against the upright of the mount allowing the track change etc to be pressed
If you want to see more I'll take some pictures in the light tomorrow.
"I know that you believe that you understood what you think I said, but I am not sure you realize that what you read is not what I meant"
You could get one of these from dashmount and add it to the D3 bracket - i did something similar years ago with a bracket from them for a pda in my old V70 volvo
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
Law of Mechanical Repair:
find it harder to see.
