Member Since: 27 Dec 2005
Location: Zurich
Posts: 458
SDV6 Engine knocking badly inlet manifold change last week?
by a Land Rover main dealer, this is a disaster but any ideas guys please?
6th Jun 2024 3:43 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5044
Don't drive it! If the crank let's go you'll need a now engine as it will likely warp the block.
Get it transported to the garage and have it assessed.yµ (idµ - eAµ) ψ=mψ
6th Jun 2024 4:09 pm
richardch
Member Since: 27 Dec 2005
Location: Zurich
Posts: 458
thks but if the crank goes surely it would not run at all. i have no engine warning lights or fluid leakage, is it possible the LR garage didnt install one of the new injectors correctly?
6th Jun 2024 4:23 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5044
If what you are hearing is a crank bearing and you continue drive it you risk destruction of the engine.
Could it be an injector? Yes, but it might not be and I can't tell from the limited vid you posted.yµ (idµ - eAµ) ψ=mψ
6th Jun 2024 4:37 pm
richardch
Member Since: 27 Dec 2005
Location: Zurich
Posts: 458
yes thks, whatever, it is going on a flatbet at a cost of GBP 700 back to the LR main dealer in Germany tomorrow, where is the nearest railway Viaduct to jump from, I just paid GBP 4k for the inlet manifolds last week!
6th Jun 2024 4:45 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5044
Ouch yµ (idµ - eAµ) ψ=mψ
6th Jun 2024 5:15 pm
G3Z
Member Since: 16 Dec 2018
Location: South Wales
Posts: 559
Very well could be an injector not seated correctly.Defender 110 2.4 TDCi Utility Station Wagon.
2007 Disco 3 GS TDV6 Manual
200,000+ mile club 😎
6th Jun 2024 5:45 pm
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20841
Member Since: 06 Mar 2017
Location: Lost
Posts: 5044
That's what I was thinking too and after he's just shelled out the guts of 5k.yµ (idµ - eAµ) ψ=mψ
6th Jun 2024 9:11 pm
Moo D3 Decade
Member Since: 13 Aug 2010
Location: UK
Posts: 14409
Hopefully its not terminal.
Have a look at LR Time on You Tube. D4 HSE EU6 (Known as Jeeves)
New Defender L663 110 SE (known as Noddy!) Sold
Sold Volvo XC90 R-Design (known as Basil)
Sold - D4 HSE (Known as Gerty)
No longer the Old Buses original owner
231,000 miles and counting
05 S manual owned from March 2005
D4 Face lifted
Still original injectors and turbo
V8 Front brakes
BAS Remap, Allisport Intercooler and deCat
EGRs blanked
T-Max split charge
Hanibal Expeedition rack
Prospeed ladder
Duratrac tyres
IID BT
BAS FBH control
6th Jun 2024 10:02 pm
richardch
Member Since: 27 Dec 2005
Location: Zurich
Posts: 458
so hopefully its the injector but if not I guess its a new short block LR038168 and engine rebuild, how many hours does this take 15 or so ?
7th Jun 2024 12:29 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5044
Hopefully at worst it will be a big end bearing that has gone and you won't need a new block.
Crank re-grind and new main & big end bearings, gaskets & seals, and a new oil pump T/belt etc as a bare minimum. The cost will depend on the hourly rate being charged, but if the cost of your replacement manifolds is anything to go by it's going to hurt.
Try and get a fixed price for the work and a list of what components they intend to replace. Whatever they come back with it's a lot to shell out on a 12yr old car especially given you have already spent 5k.
Maybe move it on afterwards and try to recover some or most of the outlay for a newer vehicle?yµ (idµ - eAµ) ψ=mψ
7th Jun 2024 12:51 pm
richardch
Member Since: 27 Dec 2005
Location: Zurich
Posts: 458
What about a reconditioned D4 SDV6 engine, there are plenty for sale in UK & Europe, any recommendations or thoughts welcome pls?
13th Jun 2024 4:34 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5044
There is a wide variety of engine remanufacturers out there, some have high standards of workmanship and many others much less so. Either way, success or failure of these engines will very often come down to the quality of the components used during the rebuild, and not just the machining processes. A firm example of this might be the source for the crankshaft if it has to be replaced!
There are some specialist Land Rover engine rebuilders who do nothing else but Land Rover. These guys you'd expect to hold a high degree of knowledge with these engines, their respective failure points, idiosyncrasies, and what components not to use in a rebuild etc.
However, there are long held question marks regarding the origin of manufacture for crankshaft replacements used during the remanufacture process. Whether it be by Land Rover, or an aftermarket specialist, these can be sourced from a number of manufacturers based in either India, Turkey, Europe, or elsewhere. All of which will have varying standards of quality, and so it would appear (anecdotally at least) that the failure or otherwise will heavily depend on which of these sources were used for the crank replacement.
So which is the best crank? For the most part I can again only find anecdotal evidence but it would seem to point to the European manufactured cranks supplied by DEX as being the most reliable.
As for a specialist rebuilder Oval Auto's in the UK seem to be highly thought of on here, and although I have no personal dealings with them they are perhaps worth having a chat with before you decide further on what route to take.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
