Member Since: 18 Mar 2013
Location: Sydney
Posts: 931
D4 3.0 oil change - 'How To'
just finished with minimal drama and mess. thanks to Robbie and Flack for their help.
Remove oil cap and engine cover (lift firmly at each corner and it will pop off)
Locate 'bespoke' oil extractor fitting.
Vacuum out the warm oil using a 6 litre oil extractor(plenty on the net)
I got out just over 5 litres.(Engine oil was indicating low) you may get more.
Locate oil filter at rear of engine bay. It looks like this.
I used a 1 1/4 sae socket (fitted perfectly) I stuffed an old towel around the casing to catch any drips.
Inside of oil filter 'compartment' looks like this. Plastic fitting screws inside, so you won't make a mess when you pull the fitting out.
Now the tricky bit, removing the oil filter cartridge from the plastic housing. Inside the centre is a 4 clip arrangement that holds the filter in place.
Don't try and force the filter as it won't come out. There is a special tool that goes inside. I got lucky and found a plastic fitting in the garage that fitted inside the cage and pushed open the 4 clips in one go. Out came the filter
Put the new 'O' ring on the plastic housing that comes with the filter. Smear some oil on the 'O' ring. Push the filter home firmly it should be almost level with the housing.
Install housing a screw down. It's firm to screw but will 'hit bottom' and stop. Put in 5 litres of oil, run engine, check oil level and top up as required. Done!
I'll take some better photos next time.
13th Jan 2014 3:47 am
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20841
You should undo the oil filter first, as there is always some oil held in the housing, which drains into the sump when the filter is unscrewed My D3 Build Thread
Member Since: 14 Sep 2011
Location: annecy
Posts: 233
filter removal
Do the four clips push outwards or inwards to release?
If anyone knows he address of the idiot who designed this....and the addresses of the managers who approved it...
17th Jun 2015 10:38 am
motolite
Member Since: 18 Mar 2013
Location: Sydney
Posts: 931
hi, I'll have a bit of an old funnel (?) that i use, although not the exact dimensions, but it does work. outside diameter 33, inside 27. Maybe LR sell a tool? I'll check at the next official service in 2 weeks.
17th Jun 2015 10:48 pm
sceh
Member Since: 14 Sep 2011
Location: annecy
Posts: 233
Odd. The full workshop manual only mentions some kind of T-bar which you could easily make (https://jlrequipment.service-solutions.com/en-GB/Pages/ItemDetail.aspx?itemID=46829&catID=337810). The strange thing is that there are no holes in the filter into which this would engage. All the videos of this type of filter element show that it just slides out although it will expand over time and become a difficult fit.
I don't see how this tool can work
18th Jun 2015 11:27 am
motolite
Member Since: 18 Mar 2013
Location: Sydney
Posts: 931
That's interesting. When I do my next oil change in Sept I will take a closer look.
18th Jun 2015 11:35 am
sceh
Member Since: 14 Sep 2011
Location: annecy
Posts: 233
It seems the 2.7 litre engine needs this tools but the 3.0 litre engine has a different size filter. In addition, the internal cage in the filter housing does not need to be removed - the paper element is meant to come out by itself.
18th Jun 2015 11:49 am
motolite
Member Since: 18 Mar 2013
Location: Sydney
Posts: 931
Thanks sceh,the plot thickens.
18th Jun 2015 12:02 pm
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
Click image to enlarge
Land Rover - Turning Drivers into Mechanics Since 1948
I hate this idea of sucking it out any sludge (not that there should be any) would stay in the sump then I guess.Defender 300Tdi 110 HCP - Keswick Green
Discovery 4 SDV6 HSE LUX - Montalcino Red/Black Pack - Gone
Connect L2 Double Cab - Moondust Silver
Connect L1 - Moondust Silver
VW California Ocean 150PS DSG - Reflex Silver
18th Jun 2015 4:10 pm
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
Yes, just undo the sump plug.
Land Rover - Turning Drivers into Mechanics Since 1948
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
