Member Since: 08 Apr 2013
Location: Pembrokeshire
Posts: 481
Gottit
cheers robbie
CCmay the odds be ever in your favor
21st Mar 2014 7:55 am
mickdundee
Member Since: 06 Feb 2011
Location: Somewhere between the Moon & NY city
Posts: 302
How much would the stealers normally charge for recalibration ?
21st Mar 2014 9:04 am
PatGAPInnov Site Sponsor
Member Since: 02 Dec 2011
Location: Montreal
Posts: 745
Dealer would charge... too much
The individual corner calibration procedure will be redone completely in the weeks to come. It will be simplified significantly.http://www.gap-diagnostic.com/
21st Mar 2014 1:51 pm
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20841
Generally, a diagnostic charge, or an hours labour for a calibration, assuming it calibrates OK first time.
I remember spending more time than I care to remember calibrating D3's/RRS's with IDS. Everything must be accurate to what the computer expects, to a tolerance of 3mm or so, per corner...
Patrick, I fail to see how you can make it easier to adjust corner heights. Its only a few button presses as it is My D3 Build Thread
Member Since: 14 Oct 2013
Location: 'Sunny' Zomerset
Posts: 9424
Been reading this thread with interest, but am nervous as I've only had the IID tool for a few days......I think I'll now wait for the update Iggy/Ieuan
Current LR =
2015 RR Sport Autobiography
&
1992 Land Rover Defender Camper
- Gone but not forgotten:
MY10 D4 GS
MY05 Disco 3 'S'
MY14 FL2 HSE manual in Blue
MY15 Disco 4 HSE Lux in Santorini Black
MY08 Disco 3 SE manual in Buck Blue
1960 Series 2 88" (No idea why I sold it!)
21st Mar 2014 2:06 pm
PatGAPInnov Site Sponsor
Member Since: 02 Dec 2011
Location: Montreal
Posts: 745
How much do they charge per hours in the UK?
And yes, it is possible to improved Mike
Ieuan, if you need to do this calibration (sensor removed or replaced), I can give you a hand with the numbers, no worrieshttp://www.gap-diagnostic.com/
21st Mar 2014 2:10 pm
markbrads
Member Since: 15 Apr 2013
Location: East Sussex
Posts: 234
PatGAPInnov wrote:
Dealer would charge... too much
The individual corner calibration procedure will be redone completely in the weeks to come. It will be simplified significantly.
I'm looking forward to this...
My rear left hand side is higher that the rest what ever I do I can't get it to go down...
Looks bloody stupid when parked up, god only knows what people think when they are behind me
I need some help with this one - anybody
21st Mar 2014 3:04 pm
PatGAPInnov Site Sponsor
Member Since: 02 Dec 2011
Location: Montreal
Posts: 745
I've uploaded the 2 spreadsheets into my gallery, 1 Mac, 1 Excel. I'd tried earlier, but the gallery upload didn't want to accept an .xls file, so I just zipped them up and they were accepted.
I don't see how it could be much easier either, unless you just feed in the measurement, and then everything gets sorted out for you. But that takes all the fun out of it. And the feeling you accomplished something
One thing I did though that made it easier for me, is that I went off the top of the centre cap, I found that it was easier to get consistent measurements from there, rather than guessing where the actual centre was. The cap is 56mm wide, so I just added 28mm to my measurements.
Actually, the hardest part for me was finding a reasonably flat piece of land to take measurements, everywhere that's convenient for me has some sort of slope or irregularity, so, I went off to the nearest Tim Hortons parking lot and measured there. With onlookers.
21st Mar 2014 4:14 pm
PatGAPInnov Site Sponsor
Member Since: 02 Dec 2011
Location: Montreal
Posts: 745
Folks at Tim Horton must have looked at you strangely while drinking their coffee.
Measuring from the center of the rim, to the top of the center cap or anywhere else does not matter. As long as it's repeated for all 4 wheels.http://www.gap-diagnostic.com/
21st Mar 2014 4:24 pm
marco 110
Member Since: 15 Nov 2009
Location: SALLES 33
Posts: 1014
Hello.
I'll change upper rear wishbone soon should I do before or after calibration?
Certainly before 4 wheel alignment?Marco.
-D4 sdv6 HSE 2012 , high beam assist , surround cam, tv , and a lot of nice stuff..
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
what ever I do I can't get it to go down...
