Member Since: 30 Aug 2021
Location: Cheshire
Posts: 13
Thanks for the reply Motolab!
Battery was pretty high up on my list but seems to be cranking fine so tried to make it last
What is the way to test from within the car with ignition on or off as I've read about the lights but I'm not sold on it working! Can I also test usign the fob with ignition on?
Thanks again.
*I've just plugged in my scanner and the fault code B1D29-93 (No start even after restart attempt) has flagged up, is this still likely to be the battery?*
28th Nov 2021 7:49 pm
Motolab
Member Since: 18 Oct 2019
Location: Sleen
Posts: 1820
If your battery is after not using it for 12h still 12,6v no… but if it is less… probably
Since it does work when engine running..Best regards
Harold
Always looking for Pre '55's & Pre war British Motorcycles! knowing or having one for sale? PM please. I visit the UK 6 times a year
Ps. I edit my texts quite often, english is not my native language, so I will edit My “typo’s” etc.
28th Nov 2021 8:51 pm
Matty 2332
Member Since: 02 Dec 2008
Location: West Yorkshire
Posts: 670
So, fired up my FBH using my phone and the BAS tele starter. It fires up and stays on for 30 mins, however it gets up to 88 degrees centigrade. I am presuming the temp sensors have gone. I've ordered a new set but cannot find any fitting instructions. Can I do this procedure without removing the unit ?
Many thanks
8th Jun 2022 6:08 pm
Motolab
Member Since: 18 Oct 2019
Location: Sleen
Posts: 1820
Quote:
I am presuming the temp sensors have gone
why do you think THAT?? if they are gone, it doesn't work....
somewere in the software there is a line saying at which temp to go into safety. in theory it could have been altered by "someone" in the past...
but TBH.. 88 dec Celcius for cooling liq temp in an engine happens quite often, so no danger in itself.. leave it at as if there are no problems otherwise...
carburetors, ignition and FBH, people LOVE to feddle with them... Best regards
Harold
Always looking for Pre '55's & Pre war British Motorcycles! knowing or having one for sale? PM please. I visit the UK 6 times a year
Ps. I edit my texts quite often, english is not my native language, so I will edit My “typo’s” etc.
9th Jun 2022 9:38 am
Matty 2332
Member Since: 02 Dec 2008
Location: West Yorkshire
Posts: 670
Thank you Harold. I will leave it as it is
9th Jun 2022 3:16 pm
Norfolk
Member Since: 02 Feb 2015
Location: Norfolk
Posts: 76
Relocated
Last edited by Norfolk on 16th Dec 2022 2:06 pm. Edited 1 time in total
14th Dec 2022 10:56 am
cstenger
Member Since: 16 Nov 2016
Location: Duesseldorf
Posts: 8
Burner gasket
So, unfortunately I have to revive this thread too
Did any of you dig into the burner gasket topic a bit deeper? Material, thickness, number of gaskets, heat resistance?
Why are there 2 (?) gaskets? Is 250°C enough, or rather use several graphite sheets to make an own?
My FBH sometimes refuses to start. No start after 2nd attempt / no operation, sometimes even flame interuption. And while I'm at it, I want to inspect everything, including the fuel cup. Hence I need at least gasket sheet material at hand.
Cheers
Christian
15th Dec 2022 8:12 am
charlietortoise
Member Since: 29 Oct 2011
Location: Staffordshire
Posts: 511
Discovery 4 3.0 HSE 2010 year. I like it a lot. Now with winch 😂
8th Jan 2023 11:38 am
Fin-M
Member Since: 22 Jan 2023
Location: Essex
Posts: 16
Hi, having serviced with new gaskets and refitted I had a massive Coolant leak that I am assuming is coming from where the elbows attach to the FBH. I disconnected the pipes and linked them with a 20mm elbow and the leak stopped. My assumption is that the elbows into the unit are not seated properly onto the o-rings? Is this the only place they could leak? The water jacket is sealed otherwise I believe? I ran out of patience to try and re assemble this evening. (The foaming oven cleaner worked a treat)
29th Jan 2023 4:51 pm
Captain Crosscheck
Member Since: 03 Sep 2021
Location: Oslo
Posts: 340
Had a go at cleaning the FBH this evening. It's been on and off since last autumn, and I thought I'd give it a go before winter kicks in over here. Easy job to remove and disassemble the unit, and as a pleasant surprise the chamber itself was relatively clean. A going over with an old dishwashing brush removed the deposits.
The unpleasant surprise was these cracks in the burner assy:
That spells new burner to me anyway...
13th Aug 2023 3:37 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5043
Member Since: 03 Sep 2021
Location: Oslo
Posts: 340
So that's a common thing? Wish I had taken the burner apart to check the status of the burner and that wee cup. Where exactly is the temp sensor? I want to trick it with some ice to see if my cleaning improved the running at all. Might just buy the burner, half price at Island 4x4 compared to anywhere else!
13th Aug 2023 7:48 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5043
If you follow the wiring on the body you'll see it leads you to a small round sensor. I think there are two of them, one NTC and one PTC, ( temperature & overheat sensors respectively).
They are resistance sensors and if I recall correctly they are located beneath the water connectors held in situ by a metal plate. yµ (idµ - eAµ) ψ=mψ
13th Aug 2023 11:13 pm
kim0785b
Member Since: 12 Feb 2021
Location: London
Posts: 141
Discovered the fuel line on mine leads to nowhere! It has a connector but have no idea where it plugs into if anything. This was after trying everything to diagnose the FBH, turns out there is no fuel. Any advice appreciated!Discovery 4
Oct 2015, 2016 build
SDV6 Santorini Black SE
New engine at 42k
Car camper
9th Jan 2024 7:01 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5043
The fuel pump is fed via a fuel feed line from the tank lpfp housing. The pump itself is located on the crossmember just forward of the fuel tank. It's a solenoid type pump (pulse signal). From there an output fuel line runs along the crossmember and up the passenger side of the engine where it then meets the FBH.
You can't run a continuous current to test the pump as this would damage it. If you have a suitable diagnostic tool (GAP) you can test the pump. It can be heard pulsing when operating or in test mode.yµ (idµ - eAµ) ψ=mψ
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
