Advertise on DISCO4.COM
Forum · Gallery · Wiki · Shop · Sponsors
DISCO4.COM > Maintenance & Mods (D3)

Front Driveshaft CV Boot replacement
Post Reply  Down to end
Page 1 of 1
Sea Raider
 


Member Since: 01 Nov 2016
Location: None
Posts: 4450

Front Driveshaft CV Boot replacement

Currently replacing a failed CV boot and as the shaft has only done 45,000 miles decided to replace both boots.
I had the shaft replaced with a new one.
Have fitted 3 out of the 4 clips onto the boots and on the last clip on the outer boot but its different to the other 3

(Using this excellent write up https://www.disco3.co.uk/forum/topic54694.html ) I have used the pliers and vice trick to tighten 3 clips but as per the images no raised crimp on the 4th clip
so my question is how do I tighten this one up, I didn't pay attention when I was removing the old clip, I just used a hacksaw to cut it.








Anyone?
 

Last edited by Sea Raider on 30th Jan 2020 5:25 pm. Edited 1 time in total 
Post #211709930th Jan 2020 5:06 pm
View user's profile Send private message View poster's gallery Reply with quote
lynalldiscovery
 


Member Since: 22 Dec 2009
Location: Maidstone
Posts: 7274

United Kingdom 2006 Discovery 3 TDV6 Metropolis LE Auto Bonatti GreyDiscovery 3

Iirc I tried and failed, so went with a thin stainless jubilee clip.

Was okay for a couple of years, but where I had let it run dry for to long it started to grumble, so stuck new shaft in.
  
Post #211710430th Jan 2020 5:16 pm
View user's profile Send private message View poster's gallery Reply with quote
Sea Raider
 


Member Since: 01 Nov 2016
Location: None
Posts: 4450


This was advertised as a GKN kit with a 2 year guarantee from Maltings
  
Post #211710630th Jan 2020 5:22 pm
View user's profile Send private message View poster's gallery Reply with quote
rrhool
 


Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4507

United Kingdom 2007 Discovery 3 TDV6 SE Manual Zermatt SilverDiscovery 3

Grip the raised 'nodules' with your pliers, and it should just ratchet tighter, and hold its position. You might have to hold down the free end with your finger to make it latch.
 Richard


D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.



Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone 
 
Post #211710930th Jan 2020 5:25 pm
View user's profile Send private message View poster's gallery Reply with quote
Sea Raider
 


Member Since: 01 Nov 2016
Location: None
Posts: 4450


All sorted

Small pipe wrench and pair of pliers

Well happy





All cleaned out and new grease filled
  
Post #211716030th Jan 2020 7:43 pm
View user's profile Send private message View poster's gallery Reply with quote
rrhool
 


Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4507

United Kingdom 2007 Discovery 3 TDV6 SE Manual Zermatt SilverDiscovery 3

Thumbs Up
 Richard


D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.



Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone 
 
Post #211717230th Jan 2020 8:04 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO4.COM is independent and not affiliated to Land Rover.
Switch to Mobile Site