Baz31
Member Since: 23 Apr 2019
Location: Swadlincote
Posts: 121
|
Droning when turning right |
|
Hi
When I am going round a right hand bend there is a droning noise that gets louder the faster and tighter the bend.
I have had the wheel bearings checked by the garage and no advisory on mot 2 weeks ago so not sure where to look next.
Doesn’t seem there when turning left.
It sort of sounds like when you used to put a piece of card in the spoke of your bike wheel when you were a kid.
Any advice on what I could check?
Thanks
Baz
|
18th Mar 2020 10:18 pm |
|
|
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1807
|
Does it sound more from the front or from the rear
|
19th Mar 2020 9:29 am |
|
|
L319
Member Since: 14 Dec 2013
Location: Herefordshire
Posts: 2081
|
Can you feel anything in the steering when this occurs?
|
19th Mar 2020 9:42 am |
|
|
Baz31
Member Since: 23 Apr 2019
Location: Swadlincote
Posts: 121
|
Thanks both
Been out for a drive and can report:
Does seem to be front end
Can’t feel anything through steering wheel.
Think a bit more after posting, the mot advisory were:
Play in track rod end - steering wheel is about 5 deg off
Slight play in a rear suspension arm.
Am going to try and have a wobble around Underneath at the weekend To see if there is anything obvious.
|
19th Mar 2020 4:04 pm |
|
|
Baz31
Member Since: 23 Apr 2019
Location: Swadlincote
Posts: 121
|
So had a look and couldn’t find anything amiss.
Had a long run out tonight and noticed the following
The vibration / noise can be felt through the vehicle and through the steering wheel but only slightly.
It’s worse the tighter the turn
It comes as soon as you turn to the right, even just to avoid a pot hole etc
Not there turning left
Got more noticeable at straight ahead when the car lowers itself on the motorway ( special programs off - another fault I don’t know what it is)
Am going to have track rod etc done but don’t want to go ahead and get it tracked and find out the thing that’s causing this noise needs it to be done again.
|
21st Mar 2020 11:56 pm |
|
|
pjm-84
Member Since: 04 Oct 2016
Location: Hampshire
Posts: 2566
|
Sounds like a front wheel bearing (nsf) to me. Mine was exactly the same. Mileage was circa 110k. Swapped it out and it was fine.
|
22nd Mar 2020 12:37 am |
|
|
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1807
|
+1 on wheel bearing - do both sides as the other is likely to go
|
22nd Mar 2020 12:45 am |
|
|
pjm-84
Member Since: 04 Oct 2016
Location: Hampshire
Posts: 2566
|
Yep. I did both. Odd how much quicker it is to do the second one. The four bolts at back.... I was hoping they would snap. Alas no.
|
22nd Mar 2020 12:47 am |
|
|
Hardware
Member Since: 28 Jun 2016
Location: Hiding under the M60
Posts: 12936
|
There's another thread somewhere explaining how the cornering direction tells you which wheel it is. Do a search as it's far too early for my memory to be trusted. Need at least one more coffee to class myself as being awake .
Dean
====================================
2011 D4 XS - OBD port protection, RLD spare wheel protector, All LED interiors lights, Timed Climate enabled, iiD tool paired.
2011 D4 Landmark - Stolen from same dealer before I paid for it
2011 D4 GS - Stolen whilst at dealer ... All LED interiors lights, DRLs, Spare Wheel protector.
1996 300Tdi - Eaten by tin worms
|
22nd Mar 2020 7:05 am |
|
|
Baz31
Member Since: 23 Apr 2019
Location: Swadlincote
Posts: 121
|
Thanks all.
Going to do another check and then get a hub and see if I can’t do this myself.
Hopefully that solves it, fingers crossed.
Baz
|
22nd Mar 2020 10:37 am |
|
|
pjm-84
Member Since: 04 Oct 2016
Location: Hampshire
Posts: 2566
|
Opposite side to the noise. As you turn right the weight transfers onto the left front hence the noise.
Need a big off socket for the drive shaft. My old man was an HGV fitter so I knabbed his 1in drive set and a cut down scaffold pole.
|
22nd Mar 2020 6:33 pm |
|
|
knwatkins
Member Since: 19 Sep 2018
Location: Poole, Dorset
Posts: 716
|
It's a 32mm. I did mine last weekend.
I had SWMBO with her foot on the brakes and I was jumping up and down on my breaker bar to crack it. I thought my bar was going to snap Kev
MY2014 L405 RR Vogue SE 4.4 SDV8 in Corris Grey
MY2010 L320 RRS HSE 3.0 TDV6 in Stornoway Grey
|
22nd Mar 2020 8:12 pm |
|
|
Baz31
Member Since: 23 Apr 2019
Location: Swadlincote
Posts: 121
|
Cool thanks
I am sort of thinking may get it done at same time as track rod end for ease.
Did the ones on my D2 with the help of a somebodies dewalt driver so was a dream however current situation means that’s not so easy to achieve at the moment
I need to check the paperwork with the car as am sure it has had one done already so be helpful to see which side.
Cheers again all.
|
22nd Mar 2020 10:01 pm |
|
|
knwatkins
Member Since: 19 Sep 2018
Location: Poole, Dorset
Posts: 716
|
Check out the Optimal bearings from AF Baz. £72 , 4 year warranty. Kev
MY2014 L405 RR Vogue SE 4.4 SDV8 in Corris Grey
MY2010 L320 RRS HSE 3.0 TDV6 in Stornoway Grey
|
22nd Mar 2020 10:14 pm |
|
|
Baz31
Member Since: 23 Apr 2019
Location: Swadlincote
Posts: 121
|
Brilliant will def do that, a great price.
Thank you.
|
22nd Mar 2020 10:39 pm |
|
|