Member Since: 27 Dec 2020
Location: Kings lynn
Posts: 6
Handbrake orange warning light.
Hi I have recently purchased a 2005 discovery 3 HSE Auto. When i bought the vehicle the orange handbrake warning was showing but the handbrake would operate normally using the button.
I have now purchased a Mongoose jlr to read codes etc. I have fault code c1a41-01 in epb which is clutch pedal sensor circuit. I am assuming the secondhand unit came off a manual vehicle.
When I try to reprogram the unit it keeps coming up with manual then tries to program the clutch position sensor.
Hopefully someone has come across this before and is able to help.
1st Jan 2021 5:51 pm
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1818
Just as a thought, you indicate it is an "auto" so it will not have a clutch pedal. It may be referring to the brake pedal switch which often gives odd ball problems. Check the rear brake light bulbs as well
1st Jan 2021 11:14 pm
Pobski1980
Member Since: 27 Dec 2020
Location: Kings lynn
Posts: 6
After further investigation I have found that the engine ecu, bcm and instrument cluster were replaced after water damage. Second hand units were fitted from a manual vehicle hence why it's looking for clutch pedal position.
Does any one know if engine ecu part numbers for manual and automatic vehicles are the same or different?
1st Jan 2021 11:20 pm
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1818
I always thought those ECM's where different on an auto and manual. There is a file call CCF that has many different settings. Maybe it will allow changing from manual to auto but not really sure so would wait till someone more experienced comes along.
Does it actually run with those ECM's fitted.
2nd Jan 2021 12:49 am
Pobski1980
Member Since: 27 Dec 2020
Location: Kings lynn
Posts: 6
Yes it runs and drives. My only issues are the orange handbrake warning light, HDC not working and no low range. I am beginning to think all issues are related to the Manual ecus that have been fitted.
2nd Jan 2021 8:22 am
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1818
I would think that is a good thought. It may just be the BCM one.
2nd Jan 2021 9:20 am
petekevin2004
Member Since: 30 Apr 2024
Location: Nairobi
Posts: 2
Orange handbrake warning light
My Lr3 has the same issue. the orange handbrake warning light is on, HDC not working and no low range not working. My ECU's Lockset was removed from a Manual car and fitted on my car. Anyone who can program it for me online will be great because I'm from Kenya...
11th May 2024 11:51 am
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5044
RCM, EPB, TCM, and RLM are all vin coded so they must be harvested from the same donor vehicle.
The BCM will need to come with the donor KVM,IPC, and keys.[/b]yµ (idµ - eAµ) ψ=mψ
11th May 2024 2:50 pm
petekevin2004
Member Since: 30 Apr 2024
Location: Nairobi
Posts: 2
The donor car is no longer available, and my LR3 is automatic.. which diagnostic tool can program it to read the Vehicle's VIN.?
13th May 2024 5:24 am
TheWojtek
Member Since: 23 Apr 2016
Location: Poznan, Poland
Posts: 82
PROFSR G wrote:
RCM, EPB, TCM, and RLM are all vin coded so they must be harvested from the same donor vehicle.
The BCM will need to come with the donor KVM,IPC, and keys.[/b]
Doesn't the "reinstall new module" option in JLR SDD work on them? Assuming they are the same units but with different programming, this procedure would download the latest firmware for these according to the vehicle VIN and apply it to them including actually writing down the vehicle VIN to the ECU.Wojtek
L319: dad's
L320: mine
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
