| Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Groups · Profile · Donate ·
Log In
|
- You are currently viewing DISCO4.COM as a guest - Register to take part or Log In
sasdiscos
Member Since: 22 Feb 2013
Location: Northants
Posts: 889
  
|
| A pillar trim clips LR026343, can any one confirm please? |
|
Hi every one.
Last year my A pillar trim drivers side came off in the wind, i clipped it back in and forgot about it, donut again today so want to order the new clips.
Just want to confirm, when i had the d3, i upgraded to a newer trim kit with sticker pad blanks for one hole each side.
The part number I keep finding ref to for the d4 is LR026343. So assume they released a new kit for the d4.
Is this correct and is it one set per side?
Also, at present all the clips on my a pillar trim are white, any pics i have seen show yellow and white.
Any help much appreciated as always, cheers.
Steve You remind me of a younger me, not much younger mind...perhaps even a little older!
|
 7th Feb 2021 12:27 pm |
|
|
kajtzu
Member Since: 10 Aug 2017
Location: Helsinki
Posts: 6754
  
|
That’s been superseded by LR077843. But yes, one set per side. AFAIK it’s four yellow and a white clip per side.
|
| 7th Feb 2021 12:49 pm |
|
|
sasdiscos
Member Since: 22 Feb 2013
Location: Northants
Posts: 889
|
Many thanks indeed.
I’ll order them up.
Steve You remind me of a younger me, not much younger mind...perhaps even a little older!
|
| 7th Feb 2021 1:02 pm |
|
|
Sylvester19
Member Since: 17 Jul 2020
Location: Central Scotland
Posts: 128
 
|
Just bought 2 new A pillar trims, they came with grey clips (same as LR077843) and they have the 2 plastic locating pins as well. As mentioned with the D3 tsb, lower pin should be cut off and the hole covered with a black pad to stop water ingress, so did the water ingress magically stop with the disco 4 and they kept the pin?
Just to throw another spanner in the works, the old R/H trim was held on with a yellow clip at the top and the rest grey, all the grey clips came off, the yellow one stayed in the A pillar. The L/H trim was held on with grey clips, I'm not the 1st owner, so no idea what is correct.
The fact the yellow clip is still in place would make you think they all should be yellow and the trims wouldn't flap about & part company on the motorway. The most anoying thing is the paint gets chipped around the holes, too cold to touch them up.
|
| 7th Feb 2021 11:13 pm |
|
|
sasdiscos
Member Since: 22 Feb 2013
Location: Northants
Posts: 889
|
Yes, mine has the pin still there. I don’t have any water leaks at present.
I wonder what the difference is?
Steve You remind me of a younger me, not much younger mind...perhaps even a little older!
|
| 12th Feb 2021 6:41 am |
|
|
nigethecat
Member Since: 11 Sep 2016
Location: Marnoch
Posts: 4244
|
Whichever clips you use, Sikaflex around the holes and under the trim, will stop any leaks and also ensures it stays put ! I want to see the sweets before I get into your windowless van... I'm not stupid!
Corris Grey D4 Commercial SE 2016
Zermatt Sliver 2007 D3 SE manual (gone)
Indus Silver D4 HSE 2015 (gone)
Bonatti Grey D3 HSE 2006 (gone)
White D3 S (LHD) 2007 (gone)
Firenze Red D4 HSE 2014 (gone)
Black RRS 3.6TDV8 2008 (gone)
Rusty Green Defender 110 1997 (gone)
Black FL2 HSE 2013 (gone)
|
| 12th Feb 2021 8:50 am |
|
|
Stuart Barnes
Member Since: 15 May 2020
Location: Los Angeles
Posts: 5
  
|
Here’s a vid I put together about the a pillar trims and the front cowl replacement. You can clearly see the design of the Land Rover clips differing from the cheapo aftermarket ones that were installed on mine. Also the windscreen installer did a perfectly crappy install job and scratched up the a pillar frame enough for me to spend an hour touching things up.
Hope it helps.
Stu.
|
| 21st May 2021 10:35 pm |
|
|
Sylvester19
Member Since: 17 Jul 2020
Location: Central Scotland
Posts: 128
|
Why was the windscreen cowl sitting up, good video, maybe repost it, how to replace windscreen cowl, seems to be quite common, plastic is rubbish and degrades quite quickly, expect more so in California! As a few of us have found out you can't buy the foam separately, have to buy the A pillar as well.
|
| 21st May 2021 11:24 pm |
|
|
Stuart Barnes
Member Since: 15 May 2020
Location: Los Angeles
Posts: 5
|
The left hand side foam is
CJD500030
Not sure on the right.
Thanks for the advice on renaming. Yep it was totally goosed. I think that the windshield guy just messed it up royally. There was a lot of us damage as well as you can imagine. I’m used to rust being from the uk, now I have to deal with rust free withered plastic. Ha. I know which I’d prefer. I’ve seen 5 year old cars with peeling paint. Crazy.
Stu.
|
| 22nd May 2021 12:19 am |
|
|
kajtzu
Member Since: 10 Aug 2017
Location: Helsinki
Posts: 6754
|
Somewhat of a thread resurrection but the right hand side is CJD500020. Hope this is useful for someone finding this thread af some point in the future.
|
| 1st Nov 2024 9:22 pm |
|
|
|
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
|
|
DISCO4.COM is independent and not affiliated to Land Rover.
