Watched the video from our friends over at LR Time (https://www.youtube.com/watch?v=lRZ37buT4pk)
I would like to check the idle oil pressure of my 3.0 SDV (2012) to ensure within limits before I do an oil change (over to 5W-40 DPF).
Click image to enlarge
Does anyone know where I can find details of the pressure gauge connection point? Unfortunately the video doesn't go into specific detail.
If you have any other advice on this subject area as well please let me know!
[Note that I have a IID Tool]
Cheers
15th Jan 2024 4:15 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10684
If you look at their previous video, they machined a block to act as a Y piece.
There are also different methods on this forum so worth doing a search
15th Jan 2024 5:05 pm
insertdisc4
Member Since: 22 Oct 2023
Location: CH
Posts: 11
oh right, I see. Thanks for the message!
Is there a recommended search term? I've just checked "engine oil idle check" (and similar) but not sure if there's something more specific you might advise?
15th Jan 2024 6:40 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10684
Try
Oil pressure gauge
15th Jan 2024 6:58 pm
insertdisc4
Member Since: 22 Oct 2023
Location: CH
Posts: 11
super, thanks again!
15th Jan 2024 7:00 pm
Last Boy Scout
Member Since: 12 Apr 2019
Location: Ayrshire
Posts: 140
Hi.
Hope you’re well.
Did you get anywhere with this?
Looks like I may need to do the same.
Thanks.2005 D3 HSE
2010 RRS TDV6
27th Jun 2024 8:35 am
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4523
Easiest to go off the oil pressure switch tapping. I made an extender with a side port. I thought I had a photo of it, but I can't find it a the moment.
You can just see the gauge pipe under the EGR pipe
Click image to enlarge
Click image to enlarge
Richard
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
27th Jun 2024 10:03 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14136
Hi Richard
What a superb job u done there
Reminds me I must get round fitting mine , managed to fit the digital display gauge in the RH side panel needs tidying up, did get an adaptor that accepts the gauge sensor along with the oem one, I just got a short one which has the same specs as the longer one currently fitted
Also wish to get it fitted before I go over to 5/40
Click image to enlarge
Click image to enlarge
27th Jun 2024 1:37 pm
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4523
Hi Gary, I think you had your kit before me, that's what spurred me on to get it done!
I've taken it off again now I tested the oil pressure cold/hot/idle/2000rpm etc. Didn't want to risk a leak from the gauge or the capillary pipe.
If I remember right, the oil pressure switch has an NPT thread? 1/4" NPT perhaps?Richard
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
27th Jun 2024 1:44 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14136
I think u might be right mate , went with the wired version so can leave it in without worrying about an oil feed tube
Yes that what I also got with the 1/4 NPT, do need to just finish extending the wires
Out of curiosity do u remember the pressures u got plse and if that’s with 5/30 or 5/40 plse
Many thks as always
27th Jun 2024 2:11 pm
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4523
That was 2000rpm hot engine, 5W40.
If I recall, hot idle was 0.9bar, as per spec. Still seems desperately low pressure, when my old grey Ferguson from 1949 will run 50 psi at idle!Richard
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
27th Jun 2024 3:19 pm
Last Boy Scout
Member Since: 12 Apr 2019
Location: Ayrshire
Posts: 140
Great info troops. ☺️
Where can I get my hands on the necessary bits to simply check the pressure.
Got the light coming on at hot idle. That’s with fresh oil and filter using 5/40…. 👀🤔🫣2005 D3 HSE
2010 RRS TDV6
27th Jun 2024 7:05 pm
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4523
Have you changed the oil pressure switch? It's the easiest and cheapest thing to start with. No point worrying about the pump or bearings if it's the switch at fault.Richard
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
28th Jun 2024 6:31 am
Last Boy Scout
Member Since: 12 Apr 2019
Location: Ayrshire
Posts: 140
Not I’ve not change that.
I’d like to check the pressure for myself n see what’s actually happening.2005 D3 HSE
2010 RRS TDV6
28th Jun 2024 6:37 am
insertdisc4
Member Since: 22 Oct 2023
Location: CH
Posts: 11
I didn't get round to it yet mate, had so many other jobs on. Got 10l of oil sitting there ready to go, need to get on with it in the next few weeks. Checked my filter at least, fortunately no metal particles found on first look!
Glad to see the thread pop up again though, some great inputs so far!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
