Member Since: 20 Sep 2010
Location: Israel
Posts: 160
Silicone helped and the 2 rear connectors are finally in. Cjb won't go back into the mounting because the drain pipe is blocking from above. Next to the bolt on the photo
Any tips?
30th Jan 2020 7:49 am
cestor
Member Since: 20 Sep 2010
Location: Israel
Posts: 160
Now trying with the pipe to the side of the cjb with no joy. How are you meant to route it?
30th Jan 2020 8:15 am
cestor
Member Since: 20 Sep 2010
Location: Israel
Posts: 160
Put everything back in place (squashed the pipe to the side but car didn't start.
Multiple faults showing on dash including transmission, park brakes,hdc. Bit the bullet and have taken it all out again. Looks like one of the rear connectors came detached when trying to refit the CJB because of all the faffing with the pipe.
Have now rerouted the drain pipe to go over the metal mounting plate for the CJB. As this seems to be a shorter route, I've had to cut the pipe by a few cm. Now have the joys of refitting all the connectors but hopefully will be easier this time.
String through the levers on the rear connectors to pull them down when in place is the way to go to
30th Jan 2020 8:59 am
Gary_P
Member Since: 03 May 2016
Location: Kent
Posts: 1679
Hi cestor
Really feeling for you. Been through replacement myself but was lucky enough not to have some of your challenges. I didn't have the issues getting the CJB back up again. Wondering why your pipe is in the way. Did you replace the it?
I was recommended to use the twine and pull down solution, but I couldn't get it to work. I have small hands so was lucky enough, in the end, to be able to get them back in.
Couple of things that helped me which I'll mention just in case you haven't already tried. Leave the CJB loose when refitting the connectors, and you can cock the latches a little by pulling them slightly down before placing them in their location which makes it easier to find them to pull them down.
Good luck.
CheersGary
-------------------------------------------
Discovery 4 HSE 2016MY
30th Jan 2020 7:38 pm
cestor
Member Since: 20 Sep 2010
Location: Israel
Posts: 160
Managed to get it all working after taking the cjb out again (!) and refitting it. I'm puzzled about the route the drain pipe originally took once it enters the dashboard area and I would recommend that anyone doing this in future makes note of exactly where it goes relative to the CJB before removing the old one. Maybe different because mine is LHD...
Yes, I did a total replace of the pipe rather than splice it in - it is a very small amount of extra effort.
31st Jan 2020 5:44 am
Prette
Member Since: 16 Mar 2020
Location: Previously Stoke-ST4 (pre-pandemic), Mostly The Hague (NL) partially Lyngby (DK) certainly somewhere
Posts: 160
Hi all. Today I noticed some drops from the top of A-pillar.
Previous owner said the sunroof drain issue was fixed before.
So I took a look and the right side of sunroof was full of water. Therefore the water dripping was from overflow of the sunroof channel. Nothing much impressive to be honest. Just a few drops after loads of rain.
I followed the procedure describe here in the forum.
1- air intake out to inspect the gromet. All clear.
2 - tried to pass a grass trimmer wire from below and from above. No luck. It is completely blocked from about 7-10 cm from the intake..
As you can see by the picture attached, the old gromet was replaced by the white connection.
Click image to enlarge
Which looks like this one
I tried to push either way and apparently it is very blocked. However, the foam on intake hole was also soaked.
Any ideas? (Other than remove CJB ). I rather block that right side drain.
Can I just wack it hard or that might damage something along the drain?
Thanks a lot folks
10th Jun 2020 4:50 pm
cestor
Member Since: 20 Sep 2010
Location: Israel
Posts: 160
You can try compressed air. It didn't work for me but you may have better luck
10th Jun 2020 5:23 pm
Gary_P
Member Since: 03 May 2016
Location: Kent
Posts: 1679
I'm wondering if your strimmer wire is hitting the edges of the white joining piece rather than a blockage? As stated compressed air will get around this and I've heard is a good way to unblock if there is one.
Keep us informed of progress
CheersGary
-------------------------------------------
Discovery 4 HSE 2016MY
10th Jun 2020 6:29 pm
Prette
Member Since: 16 Mar 2020
Location: Previously Stoke-ST4 (pre-pandemic), Mostly The Hague (NL) partially Lyngby (DK) certainly somewhere
Posts: 160
Unlikely because from the bottom (feeding from the air intake) I start already inside the white connector. Unless there are more connections within 10cm or so.
I will try to round the tip to see if it helps for tomorrow.
10th Jun 2020 7:32 pm
cestor
Member Since: 20 Sep 2010
Location: Israel
Posts: 160
Sounds like the blockage is in the elbow joint
11th Jun 2020 2:51 am
AL_P
Member Since: 17 Feb 2017
Location: London
Posts: 162
Sorry for the mini hijack but wanted to share something.
So I have been struggling with the blocked sunroof drains for ages and frequently tape the roof up to prevent water ingress when it looks like it might rain.
Yesterday I came up with an idea I am going to try, I have ordered a large piece of magnetic sign material, big enough to cover the whole of the sunroof area. I can put it on and take it off really easily depending if I want to be able to use the sunroof and fingers crossed it will keep the water out due to the large overlap on the edges of the sunroof. For the £20 I have paid I think its worth a try!
Incidentally I have roof rack that sits a long way forward with a light bar on it and this will also block that light through the sunroof and stop excess mud getting into the sunroof channels when off roading.BT Gap IID
11th Jun 2020 7:48 am
Prette
Member Since: 16 Mar 2020
Location: Previously Stoke-ST4 (pre-pandemic), Mostly The Hague (NL) partially Lyngby (DK) certainly somewhere
Posts: 160
cestor wrote:
Sounds like the blockage is in the elbow joint
Good point but... because the white connector goes all the way down to the elbow (see my picture above) I suppose it is unlikely to be a the elbow blocage. Unless, there is a second elbow I am not aware of . Besides, I can feed about 10cm from the water exit behind the air take grille.
I was considering to wiggle the big hose up and down to see if free-up some kink at the bottom, however, since the tube is full of water, I preferred to wait until the water dries out. (just in case any connection gets loose and flood the interior )
11th Jun 2020 8:24 am
Prette
Member Since: 16 Mar 2020
Location: Previously Stoke-ST4 (pre-pandemic), Mostly The Hague (NL) partially Lyngby (DK) certainly somewhere
Posts: 160
AL_P wrote:
Sorry for the mini hijack but wanted to share something.
Yesterday I came up with an idea I am going to try, I have ordered a large piece of magnetic sign material, big enough to cover the whole of the sunroof area.
That is actually a good idea. Do you have a link for the supplier. When not in use, this cover should help a lot.
Besides, I follow another member advise to clear the borders of the sunroof and I will use vaseline to make it tight. It was veeeeery munky, durty, crispy, cracky, horribly dirty. At least now, it will seal a bit better when closed.
11th Jun 2020 8:27 am
Prette
Member Since: 16 Mar 2020
Location: Previously Stoke-ST4 (pre-pandemic), Mostly The Hague (NL) partially Lyngby (DK) certainly somewhere
Posts: 160
Gary_P wrote:
I'm wondering if your strimmer wire is hitting the edges of the white joining piece rather than a blockage?
Keep us informed of progress
Cheers
Thanks for the tip Gary. I sharpened the edges of the strimmer wire and voila...
After some knocking here and there... now I think there might be a kink/squeeze somewhere near the junction because despite the fact that the blockage is gone, I still cannot pass the wire through. I poured some windscreen washing liquid down the sunroof drain, it comes out slowly but does.
For now... all seems to work. Let's wait and see.
PS.: I also put Vaseline around the sunroof sealing rubber for an extra help.
12th Jun 2020 4:34 pm
Gary_P
Member Since: 03 May 2016
Location: Kent
Posts: 1679
That's good news and thanks for the update. Good idea to sharpen the wire. Shame it won't [pass all the way through. It may well be a narrowing or perhaps a sharp bend?
Have you tried the strimmer wire from the other direction , sunroof opening downwards? It's worth checking there's nothing coming into the cabin by having a really good look when you pour water down from the top.
When I used the strimmer wire from the bottom output on mine, I eventually realised the wire ended up coming out under the glove box because of the split in the elbow.
Good result for now, and keep an eye on it
CheersGary
-------------------------------------------
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
). I rather block that right side drain.
. Besides, I can feed about 10cm from the water exit behind the air take grille.
to see if free-up some kink at the bottom, however, since the tube is full of water, I preferred to wait until the water dries out. (just in case any connection gets loose and flood the interior 
)
