Glynne - the Safari snorkel is watertight by virtue of a lot of cutting etc. I'm toying with the idea of an RAI. I loked at the Safari snorkel based on cost but I think it would be a lot of money and hassle to put the car right when it comes off (which it will need to as it is a company car).
The RAI should need a few minutes work with filler on two holes and a new rubber trim piece (I hope...).
For me, the main question is - how deep do you intend to go ?The next American ex-pat that calls it a "truck" is going to find out what 2.7 tons feels like on their foot...
Club "yes, I too have had the EGR's replaced..."
Club "yes, I too have had the compressor replaced..."
Club "yes, I too once had the car at the dealer for a couple of weeksnearly 4 weeksover 4 weeks...5 weeks"
Club "yes, I too have had EPB failure..."
Club "yes, I too get mysterious bings and bongs..."
29th Dec 2008 10:37 am
countrywide
Member Since: 16 Sep 2007
Location: UK
Posts: 6019
I have never understood why they don't build a RAI in as standard up the A pillar or even both air pillars. I know it would take up some room internally, but it would be worth it.
£50 for a RAI - you lucky man simon!!! I might stretch to a £100 but no more - i guess i will have to keep a beady eye out on Ebay !!
29th Dec 2008 10:44 am
GLYNNE
Member Since: 06 Oct 2006
Location: KENT
Posts: 4689
DG wrote:
Ask yourself how often you want to get water above the recommended level i.e. over the bonnet and up to the windscreen. My guess would be not often Is a snorkel going to prevent water accessing other delicate parts ?
To try and answer you, no I don't want to dive into anything to deep, and would not be my chose to do so, especially in a nice new one .
No the snorkel wont stop water flooding everything else, but my dilemma is Yes the RAI does the job well enough for anything that I might want to do, but perhaps the snorkel could do what the RAI, plus that extra security blanket just in case I balls up.
I cant find Stornaway grey
29th Dec 2008 10:47 am
GLYNNE
Member Since: 06 Oct 2006
Location: KENT
Posts: 4689
JF Lux wrote:
Glynne - the Safari snorkel is watertight by virtue of a lot of cutting etc. I'm toying with the idea of an RAI. I loked at the Safari snorkel based on cost but I think it would be a lot of money and hassle to put the car right when it comes off (which it will need to as it is a company car).
The RAI should need a few minutes work with filler on two holes and a new rubber trim piece (I hope...).
For me, the main question is - how deep do you intend to go ?
Good point, Simple fitting = Me
29th Dec 2008 10:49 am
simon
Member Since: 11 Jan 2005
Location: Shropshire
Posts: 18296
If you get to the point (and this is the point) that the snorkel would do a better job... then you will have likely had to have had all your electric's protected too as this is where the vulnerability will lye now.
But at the end of the day... fit whatever makes you feel happier
29th Dec 2008 10:50 am
MacLeod 313
Member Since: 18 Apr 2008
Location: away
Posts: 10723
Exactly Simon, cosmeticlly the RAI looks 8) , but my fitment was'nt just to look great. I work out of a concrete works where the road sweeper is either broken or the driver is off, and in the dry conditions the dust comes off my wheels and was injested by the D3.
I was worried about the D3 in the summer, so got one off of XTC, and Ken, DG, Slimer and co helped fit it. Yes it is a confidence thing, and if you go through the trouble of using a Neoprene seal or silicone where the join on the wing and RAI is will delay and water but NOT stop it.
Personally the RAI has helped a little for me, but still the dust gets in so I think the water will too. But with the RAI on she looks great, but not invincible.
For looks ONLY go RAI
For Wading ONLY go Safari
But as Simon says, you still can only go as deep as your Electrics, get them wet and you have had it
You can improve the seal of the RAI by adding some adhesive foam tape to the metal bracket that latches into the wing. What little water that does then get in via the seal and drain hole will easily drain out of the airbox holes faster than it comes in.
They are useful though: 8)
Click image to enlarge
Previously:
2005 D3 2.7 TDV6 S
1984 90 2.25 Petrol CSW
1992 90 200TDi Hard Top
1995 Discovery ES 300TDi
2003 90 TD5 Truck Cab
I can vouch for the intake on an "unprotected" LR. Took the Defender for a play on Sunday and dropped the NSF wheel into a hole on a tricky ford up near Uncle Dom (Batcombe between Cerne Abbass and Yeovil if you fancy losing your paintwork). Heart skipped as I heard a gargling noise from the air intake, but the filter was bone dry when I checked it on the other side of the river. Tide mark on the windscreen and wing vouched for the depth and validated the state of the driver's seat I know it's not considered "kind" to say no these days, but no. Just no, ok? And if it's not ok, still no.
29th Dec 2008 9:48 pm
Antman
Member Since: 18 Dec 2008
Location: East London
Posts: 14
Reading all the feedback and comments - thanks for this I think for my purposes the LR RAI is the way to go IF it does not require the body work to be cut to fit the vehicle My reason for this is the RAI is there for emergencies in my opinion, for those cases where your front right wheel drops in a hole while crossing a river, as pointed out, in this case the flow of water into the AI will be slow and will drain out before doing damage. Same goes for dust inhalation which will be much slower.
However, if you dont mind someone cutting your body panels then the Safari snorkel is a no brainer.
It does amaze me that LR manufacture a RAI that does not seal - someone's design skills needs to be checked
If body panel chopping is required for both, then caution will need to be the order of the day and no RAI for me.
You will need to drill 2 holes in the wing, just above the air intake, and another in the a-pillar next to the windscreen. I don't have the RAI fitted all the time, so the holes in the wing (which have Rivet nuts inserted) are blanked off.
Click image to enlarge
Previously:
2005 D3 2.7 TDV6 S
1984 90 2.25 Petrol CSW
1992 90 200TDi Hard Top
1995 Discovery ES 300TDi
2003 90 TD5 Truck Cab
30th Dec 2008 3:57 pm
DiscoStu
Member Since: 09 Apr 2006
Location: London
Posts: 11412
Antman wrote:
It does amaze me that LR manufacture a RAI that does not seal - someone's design skills needs to be checked
If it were sealed it would encourage people to drive deeper than they should. The normal intake is above the water line at maximum wading depthDisco 5 HSE Lux
https://www.youtube.com/watch?v=peyiqaJrmMU
30th Dec 2008 4:02 pm
MacLeod 313
Member Since: 18 Apr 2008
Location: away
Posts: 10723
the hole in the windsreen pillar is there already, behind the black trim. Just remove the screw and replace with rivnut
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum