DiscoStu
Member Since: 09 Apr 2006
Location: London
Posts: 11412
|
Fitted the electrics this afternoon - almost. Thanks to Gareth and rbees once again for the invaluable information. Under the bonnet, no problem at all. Under the dash, though - could not move the green plug (below the fuse box) for love nor money  The black wire for plugging into it has ended up slightly short too and will need rerouting, but I ran out of light so I'll have to try again later in the week.
Why don't they do LH and RH instructions? Gareth - don't know how you did it without any help. I certainly would have been stumped without the info in this thread. Disco 5 HSE Lux
https://www.youtube.com/watch?v=peyiqaJrmMU
|
 14th Jan 2007 6:54 pm |
|
|
Gareth
Site Moderator
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 26772
|
I used to repair aircraft for a living. The planes I used to fix were all British built military aircraft, so I'm used to crap drawings 
|
| 14th Jan 2007 9:44 pm |
|
|
|
|
|
|
nwoods
Member Since: 03 Apr 2006
Location: Southern California
Posts: 563
  
|
Tami, I'll measure it for you tonight. However, I really think you'd be happier with some nice IPF's or Hella's. These 55w lights are dimmer than the stock halogen headlights, let alone the Xeon's if that's what you've got.
|
| 6th Jul 2007 12:12 am |
|
|
sideview
Member Since: 02 Dec 2006
Location: in the valley
Posts: 1663
|
Thanks very much Nathan! I'm not planning on getting the LR ones, but trying to figure out what size they are in comparison for finding some, don't wanna go too big or small & have it look funny.  The LR ones look just the right size aesthetically.  I'm not so good at giving advice...may I offer you a sarcastic comment instead?
Haiti Earthquake Relief: Donate Your Frequent Flier Miles
|
| 6th Jul 2007 12:22 am |
|
|
obscidian
Member Since: 13 Feb 2008
Location: Glasgow
Posts: 10
 
|
| Adjusting the position of the light beams |
|
Can anyone tell me how to adjust the angle of the front spots. Mine seem to be pointing at low flying aircraft ?
|
| 4th Mar 2008 9:09 pm |
|
|
Gareth
Site Moderator
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 26772
|
If you remove the Land Rover badge, there is a toothed wheel that you 'might' be able to loosen to adjust the angle. If its too tight, then remove the cross-head screws from the side of the light and pull the beam unit out of the case. You will see a 10mm nut in the centre of the toothed wheel, slacken it a touch and align the lamps.
Its a bit trial and error with the second method, because you will have to temp fit the beam unit to check your alignment. Once its aligned, use the 10mm nut to really tighten the bracket. They do tend to move if its not very tight.
|
| 4th Mar 2008 9:17 pm |
|
|
Aubrey
Member Since: 10 Sep 2006
Location: Johannesburg
Posts: 76
 
|
Have these lights on and not very happy with output. Has anybody fitted a HID kit to these? BTW, are the H3 bulbs?
Regards
Aubrey
|
| 4th Apr 2008 6:20 am |
|
|
philhunt
Member Since: 16 Sep 2007
Location: MI5 not 9 to 5
Posts: 1761
|
The bulb size for LR Driving Lamps is H1
|
| 5th Apr 2008 3:25 pm |
|
|
Spoons
Member Since: 22 Dec 2007
Location: Derbyshire
Posts: 186
|
I really like the idea of the extra bumper mounted lights, but a bit dubious about the LR units themselves. Is it possible to buy the wiring loom, switch, relays, bumper mounts etc with out the actual lights and use another 'better' manufacturers lights?
If so, can anyone give the part numbers?
|
| 17th May 2008 9:25 pm |
|
|
craig
Member Since: 08 Aug 2006
Location: Home of LR.
Posts: 2545
|
Spoons - yes of course you can get the looms etc and do it piecemeal, but the LR units aint that bad chap. The LR units give you all the pieces, so you can add better lights at a later date.
|
| 18th May 2008 8:28 pm |
|
|
10forcash
Member Since: 09 Jun 2005
Location: Ubique
Posts: 16534
|
The LR wiring is only available with the LR lights, the switch & mounting frame is available seperately
|
| 18th May 2008 8:44 pm |
|
|
Spoons
Member Since: 22 Dec 2007
Location: Derbyshire
Posts: 186
|
OK, if I go with the LR kit, what are the immediate options for increasing light output, bulbs or new units?
|
| 26th May 2008 1:51 pm |
|
|
IND TDV6
Member Since: 18 Jun 2007
Location: Indonesia
Posts: 6
|
I recently had the driving lights fitted by the dealer, but I didnt realize that they are only on with the main beam which I dont use much unless I use the "flash to pass" feature. Is there someway to ge them working with the low beam ? ____________________
D3 TDV6 HSE
Mercedes ML 350
Mercedes 280 GE
Mercedes CLS 55 AMG
BMW R1200GS
Piaggio MP3
|
| 29th May 2008 4:37 am |
|
|
