Member Since: 05 May 2009
Location: Bergen
Posts: 1509
not raining in Bergen today
Can you see the new modual with FM ?IDTOOL PRO / Faultmate programing and BAS remaping services in Norway.
Diagnostic for most Land rover vehicles
Land Rover parts and accessories.
Stockist of RLD equipment.
www.praesto4x4.no
D4 gone, missed but replaced with a 110 Puma.
25th Jun 2012 4:57 pm
SteveNorman
Member Since: 14 Oct 2005
Location: Somerset
Posts: 1146
I don't know, hopefully colin will be along in a moment to explain.
I just use SDD & press program new module
........ which usually fails the calibrate procedure & you have to do it again.
Oh & when the workshop manual was written they assumed T4 was going to carry on, so the say use T4, but they mean IDS... which is now SDD
regards
Steve
25th Jun 2012 7:17 pm
parrafin23
Member Since: 04 Dec 2011
Location: Buskeud
Posts: 681
I havent had the time to install the module yet. But today is a fine day to do it. partly cloudy with some rain drops.
Not raining in Bergen? I've heard it always rains there.. hehe..
I hope Colin can make a comment on how to. That would be great. I bet I get an error message from the FM telling me that its licensed to another vehicle..
Ill give it a go now and post back later..
P.
26th Jun 2012 4:15 pm
DSL Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 73094
Bergen, the only place I've seem umbrellas in vending machines!!
26th Jun 2012 4:29 pm
parrafin23
Member Since: 04 Dec 2011
Location: Buskeud
Posts: 681
now the low ratio icon is flashing green in the ipac. now what?
snapshot :
[/img]
26th Jun 2012 4:57 pm
parrafin23
Member Since: 04 Dec 2011
Location: Buskeud
Posts: 681
cold_n_wet wrote:
not raining in Bergen today
Can you see the new modual with FM ?
aye.. I see it..
26th Jun 2012 7:32 pm
SteveNorman
Member Since: 14 Oct 2005
Location: Somerset
Posts: 1146
It means it hasn't been coded/calibrated..... how you do that with MSV2 I don't know
regards
Steve
27th Jun 2012 5:05 am
Fogga
Member Since: 20 Jul 2009
Location: Tromsoe
Posts: 89
parrafin23 wrote:
Not raining in Bergen? I've heard it always rains there.. hehe..
It only rain two times per year in Bergen. From april to september, and from october to march.
28th Jun 2012 12:32 am
cold_n_wet
Member Since: 05 May 2009
Location: Bergen
Posts: 1509
IDTOOL PRO / Faultmate programing and BAS remaping services in Norway.
Diagnostic for most Land rover vehicles
Land Rover parts and accessories.
Stockist of RLD equipment.
www.praesto4x4.no
D4 gone, missed but replaced with a 110 Puma.
28th Jun 2012 4:42 pm
cold_n_wet
Member Since: 05 May 2009
Location: Bergen
Posts: 1509
look in other for clutch calibration.
IDTOOL PRO / Faultmate programing and BAS remaping services in Norway.
Diagnostic for most Land rover vehicles
Land Rover parts and accessories.
Stockist of RLD equipment.
www.praesto4x4.no
D4 gone, missed but replaced with a 110 Puma.
28th Jun 2012 4:44 pm
parrafin23
Member Since: 04 Dec 2011
Location: Buskeud
Posts: 681
Now I have Calibrated the clutch. the posses went good. It changed from high to low ratio and then back again. so the new module works perfect.. my old module did just the same. calibrate clutch and it did so with no issue.
After a bit more investigation.. all terrain control module.. is has failed I guess. it has no software installed. All fields says not supported. but the legacy number shows info.. cant remember exact. Sometimes I cant read it. Im getting this long error message about can not communicate with ecu. I tried writing new software to it, but failed.. lost communication to the ecu.
So.. where is this b d located?
Is it something I can open up and check for short to ground? that is the fault info I get..
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum