Member Since: 21 Apr 2013
Location: Scotland
Posts: 10
My Torx bolt on disc is chewed, cant get disc offplease help
I have my t50 torx bit and that is fine.
i went to take the torx screw out so i could get my dist off and this is all chewed up.
The t50 torx bit just spins inside it. how can i get this off?
Also where can i get a new torx bolt for my disct?
thanks any help would be very appreciated
5th May 2013 3:46 pm
n0ct0
Member Since: 19 Apr 2013
Location: Yorkshire
Posts: 4
You could try an easy-out. I've also got rounded torx bolts out by hammering in an old Allen bit.
5th May 2013 3:52 pm
dingdongs
Member Since: 30 May 2012
Location: St. Lawrence Bay Essex
Posts: 186
drill the head off.then remove disc.chance is the taper is holding it tight.thread will probably come out once disc is removed and if not can weld a nut to the protruding thread or drill out or even drill and tap a thread at the next pitch.
5th May 2013 4:10 pm
Dukey
Member Since: 21 Apr 2013
Location: Scotland
Posts: 10
thank for that, where would i find a new t50 screw?
does anyone know the size of screw in? thanks
5th May 2013 4:31 pm
bellautos
Member Since: 02 Feb 2006
Location: NorthYorkshire
Posts: 2532
Hit it square on with a flat ended punch or socket extension bar, this will shock the threads a little. Then get a small point punch or the edge or a small sharp chisel and put it at 9oclock on the left side of the head and hit it downwards. It should free off and come out.
Pete.
5th May 2013 4:34 pm
Dukey
Member Since: 21 Apr 2013
Location: Scotland
Posts: 10
thanks a lot i thi9nk this is going to work. my only issue is i cant fine where to get a new nut for it?
if you know that would be great
5th May 2013 4:56 pm
bellautos
Member Since: 02 Feb 2006
Location: NorthYorkshire
Posts: 2532
It's not the end of the world. The wheel will hold the disc on
5th May 2013 5:01 pm
john watson
Member Since: 10 Nov 2011
Location: lanark
Posts: 966
drill the head off. Chances are it will not move. Drill out the core for a 10mm x 1.5 mm thread. You will get the core size from an google search. Then re tap hole, use a 10mm x 1.5 pitch tap too clear out the remains of the screw thread
New c'sk screw from any L R dealer about £ 1.20 last time I did it (last year) or from the internet but postage probably more than the cost of the screw!!!!
5th May 2013 6:15 pm
Dukey
Member Since: 21 Apr 2013
Location: Scotland
Posts: 10
hi john thanks a lot for that reply.
i have googled for a while now on the size of this nut and i cannot find the size or the correct name for this nut, i also cannot find anywhere online to buy a replacement 1. this information would be very greaful. thanks again buddy
Part number is SYP100241 .. gooogle will work better now Cheers Ian
___________________________________________
MY13 FL2 HSE lux - just gone
MY10 D4 XS
MY07 D3 SE
Massey Ferguson 400 FIS AGTV - Arctic Cat by any other name...
Citroen C3 Picasso for SWMBO so we can remember what fuel economy is!!
Member of the Narpy torch club
5th May 2013 7:04 pm
john watson
Member Since: 10 Nov 2011
Location: lanark
Posts: 966
drill through the countersunk screw using a 4mm drill, then open out with a 8.5 mm drill. This should take out most of the thread that's left in the hole. Use a 10mm x 1.5 pitch taper tap to clean the hole out. The screw does not really do anything other than hold the disc in position so is not load bearing.
Try to keep the drill as square to the screw as you can -you do not want to end up with thread on one side and none on the other.
Use decent quality drills although the screw seems to be maqde of some sort of poor quality steel- typical of L R
As I wrote go to your local Land Rover Dealer - you will mget one there or try A BMW /Mini dealer. You are looking for torx T50 Countersunk Screw. I see you have the part number.
6th May 2013 7:20 am
amazing
Member Since: 05 Mar 2011
Location: chengdu
Posts: 1542
8.4mm drill for M10x1.5.
Have also used a hammered allen socket with sucess.
or drill head then when disk is off wack it and use mole grips to remove remaining threaded part.
in future always wack em before unscrewing
In the past bought fromn B nQ had some slotted M10 countersunk that would workIt is better to have and not need it then need and not have it.
6th May 2013 8:01 am
Bodsy Site Sponsor
Member Since: 06 Nov 2006
Location: In the Clubhouse
Posts: 21361
bellautos wrote:
Hit it square on with a flat ended punch or socket extension bar, this will shock the threads a little. Then get a small point punch or the edge or a small sharp chisel and put it at 9oclock on the left side of the head and hit it downwards. It should free off and come out.
Pete.
I use Petes method, never failed yet on even the most stubborn ones.Bodsys Brake Bible
Clock/ SNOTM /3Flash / 4x4Info /BT Update /Service Reset/Error Codes / Gearbox Reset See It Here
6th May 2013 10:26 am
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
Lots of methods out there and have had good success peening back the head with a hammer, which also shocks it; driving in socket torx or allen key; driving it around with a punch or drilling it out.
As I always have small cordless drill to hand I tend to drill out really difficult screws that are mounted on an open backed hub (ie not a blind hole). The head (and the rotor) comes off with a larger bit and I then drill through the remaining part with a much smaller RH bit. The smaller bit stays well clear of the threads but with the release of the head, the heat, the vibration and the removal of the screw core sees the screw pop out the other side.
Edit: As per this:
As with all such removals heat and vibration are your friends. I use a small cordless impact wrench these days and have never had a failure since. The effective torque is easily enough to remove the screw but without ever damaging it. Takes away all the stress!
Land Rover - Turning Drivers into Mechanics Since 1948
Member Since: 02 May 2023
Location: Trowbridge
Posts: 141
I just snapped my torx bit trying to get this thing out. The bolt is still in good shape though. I think the shocking it trick is what I’m missing. The question is though what is the best tool for the Torx? Is it just torx bits for a ratchet or is a fixed piece L-shape tool the better bet? Is an impact bit worth using?
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum