- You are currently viewing DISCO4.COM as a guest - Register to take part or Log In
Huge Halford
Member Since: 30 May 2013
Location: West Midlands
Posts: 275
  
|
Hi Guys…
I have fitted a brand new fuel burning heater and the fuel pump that runs it
Has anyone in the Midlands got the webasto software and leads to adjust the co2 level as the FBH runs for 45 seconds then enters the cool down cycle.. I have been informed by a Discovery 3 expert that adjusting the co2 level could get it running. Mods:-
Beanie Grill,Side Steps,Colour-coded wheel arches, Door handles and Bumpers,Rear Bumper Exhaust Trim,Remote Start FBH,2014 D4 rear lights,Reversing camera GVIF enabled,D4 Bluetooth Module, Puddle lighted wing mirrors
To do list:-
Waxoyl the Underside.
|
 13th Nov 2022 6:56 pm |
|
|
riverblanche
Member Since: 31 Aug 2010
Location: retford'ish
Posts: 2226
|
Hi,
word of warning ISTR adjusting that figure and get it wrong can then mean it does not fire up again, which in turn means you can not alter it back again either 
It has been mentioned before, research well before changing it ISTR it is set by factory for each unit when new, so a new FBH should not need changing it was an old unit that was not running right already that got altered .
it was some time back mind 
software if free and leads are straight forward to make up if not in Martins shop
 Transit! 2019
Gone D3 HSE 2008
Another Porsche Cayenne 2022
Gone Porsche Cayenne 2020
Gone RRS HSE Dynamic 2016
Gone RRS HSE LUX 2011
Gone RRS HSE 2006
Gone D3 SE 2.7 2008
gone D2 Td5 1999
I plan on living forever and so far so good !
Club DG Mclaren stuff
.
|
| 13th Nov 2022 10:15 pm |
|
|
Flatlander
Member Since: 20 Jul 2015
Location: Here
Posts: 575
|
So what happens if you swap control boards?
In my experience, if the FBH is capable of firing up, it will - even with a different control board with (presumably) different combustion measurements stored. I suppose it depends how different the measurements are and how far towards the edge of the 99th percentile the FBH is.
|
| 13th Nov 2022 10:21 pm |
|
|
Motolab
Member Since: 18 Oct 2019
Location: Sleen
Posts: 1820
 
|
| Re: Webasto software help |
|
Huge Halford wrote:as the FBH runs for 45 seconds then enters the cool down cycle..
What is “running” ? Blowing? buzzing? Does it generate heat in those 45 seconds?
The ecu does a check every start, if something hardware related is not ok during those checks, it wil blow, buzz, but not heat for about that same 45 secs, has nothing to do with co2
Does the fuel dosing/ meteringpump starts ticking? Tik, tik tik tik, tik
If it it starts to heat in those 45 seconds and then stops it is in 90% of the time, a blockage in the inlet or exhaust, wrong air surge under the car, etc… or a fuel blockage, like air bubbles or leakage in the fuel line…. Best regards
Harold
Always looking for Pre '55's & Pre war British Motorcycles! knowing or having one for sale? PM please. I visit the UK 6 times a year
Ps. I edit my texts quite often, english is not my native language, so I will edit My “typo’s” etc. 
|
| 13th Nov 2022 10:32 pm |
|
|
Huge Halford
Member Since: 30 May 2013
Location: West Midlands
Posts: 275
|
What is “running” ? Blowing? buzzing? Does it generate heat in those 45 seconds? ……..YES
Does the fuel dosing/ meteringpump starts ticking? Tik, tik tik tik, tik ……… YES
Can’t find a leak in the fuel line, if primed with the IIB Diagnostic tool loads of smoke for the 45 seconds. Mods:-
Beanie Grill,Side Steps,Colour-coded wheel arches, Door handles and Bumpers,Rear Bumper Exhaust Trim,Remote Start FBH,2014 D4 rear lights,Reversing camera GVIF enabled,D4 Bluetooth Module, Puddle lighted wing mirrors
To do list:-
Waxoyl the Underside.
|
| 24th Nov 2022 6:15 pm |
|
|
Motolab
Member Since: 18 Oct 2019
Location: Sleen
Posts: 1820
|
Priming, may ONLY be used when the fuel line is empty, otherwise it will flood the burner
and since diesel does not evaporate as gasoline does, it wil not ignite….
The heat you feel in those 45 seconds is from the glowplug…
I am afraid you need to dismantle it and clean it…
If done /trying too often, the resistance of the glowplug will get to high and stop doing its function…
I read it here on the forum everytime… priming (why? Because they can, with their idd/w-bus diag  ) making more trouble than there was…
Diesel is not gasoline, so no tickling or choke etc. Needed….
You can try to blow lots and lots of air through the inlet, for a looooong time…. Maybe you can get rid of excessive diesel that way… Best regards
Harold
Always looking for Pre '55's & Pre war British Motorcycles! knowing or having one for sale? PM please. I visit the UK 6 times a year
Ps. I edit my texts quite often, english is not my native language, so I will edit My “typo’s” etc.
|
| 24th Nov 2022 7:43 pm |
|
|
Huge Halford
Member Since: 30 May 2013
Location: West Midlands
Posts: 275
|
Guys from the Altox I get CODE 02 No start
1)The reason for the air intake pipe or exhaust gases. 2) The reason for the fuel system. 3) Check the pump dispenser. 4) Check the electrical system pin filament.
New Air intake pipe on a brand new FBH.
Fuel system is delivering fuel( heat and smoke for 45 seconds.)
New pump fitted.
So only things to check / change is the exhaust and what electrical system pin filament does this mean ???
Is the the wires feeding the FBH or something internally??? Mods:-
Beanie Grill,Side Steps,Colour-coded wheel arches, Door handles and Bumpers,Rear Bumper Exhaust Trim,Remote Start FBH,2014 D4 rear lights,Reversing camera GVIF enabled,D4 Bluetooth Module, Puddle lighted wing mirrors
To do list:-
Waxoyl the Underside.
|
| 25th Nov 2022 7:13 pm |
|
|
Motolab
Member Since: 18 Oct 2019
Location: Sleen
Posts: 1820
|
Please read my answer…
Excessive diesel in the burner unit does give those code’s Best regards
Harold
Always looking for Pre '55's & Pre war British Motorcycles! knowing or having one for sale? PM please. I visit the UK 6 times a year
Ps. I edit my texts quite often, english is not my native language, so I will edit My “typo’s” etc.
|
| 26th Nov 2022 5:41 pm |
|
|
Huge Halford
Member Since: 30 May 2013
Location: West Midlands
Posts: 275
|
Motolab, I have read read your answer…
I removed the FBH stripped it down cleaned out the diesel residue as per your previous reply, reinstalled the FBH,ran the vehicle to ensure coolant was circulating, attempted to fire the heater and the same procedure occurred.(ran for 45 seconds then cool-down) Read the fault code. Mods:-
Beanie Grill,Side Steps,Colour-coded wheel arches, Door handles and Bumpers,Rear Bumper Exhaust Trim,Remote Start FBH,2014 D4 rear lights,Reversing camera GVIF enabled,D4 Bluetooth Module, Puddle lighted wing mirrors
To do list:-
Waxoyl the Underside.
|
| 26th Nov 2022 6:01 pm |
|
|
|
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
|
|
