Maintenance stuff |
 |
| TITLE |
+ |
- |
| FILE NAME |
+ |
- |
| DATE |
+ |
- |
| POSITION |
+ |
- |
|
|
New rear brakes24 views
|
|
Old front lower wishbone25 views
|
|
Sawn off bush16 views
|
|
15 views
|
|
Sawn right thru the bolt and bush sleeve20 views
|
|
Managed to hold the rubber bit with an old spanner23 views
|
|
It's finally off35 views
|
|
4 new General Grabber ATs suppled by these guys in Colchester35 views
|
|
New General Grabber ATs fitted today (14.1.2013)26 views
|
|
Old black stuff comes out13 views
|
|
Draining the last bit out of the sump15 views
|
|
Weep around the Mechatronic Plug....12 views
|
|
Millers Millermatic DM Premium ATF going in via the funnel12 views
|
|
The good stuff going into the oil cooler11 views
|
|
Using the stepladder method as approved by Oswiperus!14 views
|
|
Using the Hawkeye to check transmission temp - getting there...13 views
|
|
Checking the final level at the drain plug13 views
|
|
EGR replacement28 viewsUndoing the right hand valve is much easier that the left one.....
|
|
EGR replacement17 viewsThese horrible T30 bolts hold the original onto the EGR cooler. Replaced with nice new M8x16mm bolts
|
|
EGR replacement19 viewsNew one v old one!
|
|
EGR replacement18 viewsLeft side - where the hell is it?
|
|
EGR replacement18 viewsNew valve in place. Looking nice and shiny!
|
|
EGR replacement19 viewsThe left EGR valve is tight up against the turbo boost pipe. This make insertion of the long bolts difficult!
|
|
EGR replacement16 viewsBack of left EGR cooler was a swine to replace the clip. Bound it with wire before using pincers to clip together.
|
|
EGR replacement20 viewsNew one in place. Old T30 bolts used on top replacing old rusty ones. Good access here!
|
|
EGR replacement13 viewsWhile doing stuff on the engine. Good idea to clean yer MAF. Brake cleaner and air used to get it clean again
|
|
EGR replacement18 viewsOpening the actuator for inspection.
|
|
EGR replacement19 viewsOpening up the actuator reveals that all was OK. Even the ball races are OK
|
|
EGR replacement16 viewsOld value with soot cleaned off with wire brush!
|
|
EGR replacement17 viewsCarbon build up under the flange in the sliding shaft
|
|
18 views
|
|
New pump and seal14 views
|
|
12 views
|
|
New pump showing reinforced casting of the tensioner mount13 views
|
|
New pump showing reinforced casting of the tensioner mount10 views
|
|
New cam belt, idlers and tensioner9 views
|
|
New Dayco HPFP belt and tensioner10 views
|
|
Wiring looms and cooling pipes need to be moved out the way12 views
|
|
Rear belt cover11 views
|
|
Rear HPFP belt and tensioner11 views
|
|
Remove all the stuff to reveal the cam belt and gear9 views
|
|
Alternator needs to come out17 views
|
|
Cable must be removed first10 views
|
|
Starter only needs to be moved out of the way12 views
|
|
Flywheel locking tool in place11 views
|
|
Old pump design has a weak point on the tensioner mount11 views
|
|
New pump design has the reinforced casting for the tensioner mount11 views
|
|
Old oil pump and new oil pump comparison16 views
|
|
Old oil pump removed13 views
|
|
New oil pump in place12 views
|
|
New belt, idlers and tensioner in place10 views
|
|
Britpart cambelt locking kit9 views
|
|
Damages the first seal causing it to leak10 views
|
|
How to get a leaking seal out without causing damage10 views
|
|
Advanced Factors supply oil pump seal from Victor Reinz with an insertion sleeve13 views
|
|
Plastic insertion sleeve10 views
|
|
Insertion sleeve fits onto the end of the crankshaft12 views
|
|
The new seal slides easily off the plastic insertion sleeve onto the crankshaft11 views
|
|
Used a large impact socket to tap the seal in place10 views
|
|
New seal in place on new oil pump11 views
|
|
100nM is not that tight.....11 views
|
|
Important to add the + 90 deg marked at 12 o'clock to assist10 views
|
|
Crank bolt tightening to 100nM + 90 deg10 views
|
|
17 views
|
|
Turbo Change15 viewsWhere is it?!
|
|
19 views
|
|
Turbo Change15 viewsGoing Caving
|
|
17 views
|
|
Turbo Change15 viewsDrilling out the old studs
|
|
Turbo Change19 viewsTurbo hoses were upgraded to silicone jobbies
|
|
Turbo Change17 viewsNice shiny new Borg Warner turbo
|
|
Lights on dashboard!25 views
|
|
Display showing suspension lowering!23 views
|
|
|
|
|
|
|
