| Last additions - Maintenance stuff |
13 views04 Mar 2015
|
|
New pump showing reinforced casting of the tensioner mount10 views04 Mar 2015
|
|
New pump and seal15 views04 Mar 2015
|
|
New pump showing reinforced casting of the tensioner mount13 views04 Mar 2015
|
|
New cam belt, idlers and tensioner9 views04 Mar 2015
|
|
New Dayco HPFP belt and tensioner11 views04 Mar 2015
|
|
Wiring looms and cooling pipes need to be moved out the way13 views04 Mar 2015
|
|
Rear belt cover11 views04 Mar 2015
|
|
Rear HPFP belt and tensioner12 views04 Mar 2015
|
|
Remove all the stuff to reveal the cam belt and gear11 views04 Mar 2015
|
|
Alternator needs to come out17 views04 Mar 2015
|
|
Cable must be removed first10 views04 Mar 2015
|
|
Starter only needs to be moved out of the way13 views04 Mar 2015
|
|
Old pump design has a weak point on the tensioner mount12 views04 Mar 2015
|
|
New pump design has the reinforced casting for the tensioner mount13 views04 Mar 2015
|
|
Old oil pump and new oil pump comparison17 views04 Mar 2015
|
|
Old oil pump removed14 views04 Mar 2015
|
|
New oil pump in place12 views04 Mar 2015
|
|
New belt, idlers and tensioner in place10 views04 Mar 2015
|
|
Britpart cambelt locking kit10 views04 Mar 2015
|
|
Damages the first seal causing it to leak11 views04 Mar 2015
|
|
How to get a leaking seal out without causing damage11 views04 Mar 2015
|
|
Advanced Factors supply oil pump seal from Victor Reinz with an insertion sleeve14 views04 Mar 2015
|
|
Plastic insertion sleeve10 views04 Mar 2015
|
|
Insertion sleeve fits onto the end of the crankshaft14 views04 Mar 2015
|
|
The new seal slides easily off the plastic insertion sleeve onto the crankshaft11 views04 Mar 2015
|
|
Used a large impact socket to tap the seal in place12 views04 Mar 2015
|
|
New seal in place on new oil pump11 views04 Mar 2015
|
|
100nM is not that tight.....11 views04 Mar 2015
|
|
Important to add the + 90 deg marked at 12 o'clock to assist11 views04 Mar 2015
|
|
Crank bolt tightening to 100nM + 90 deg10 views04 Mar 2015
|
|
Flywheel locking tool in place12 views04 Mar 2015
|
|
Turbo Change18 viewsNice shiny new Borg Warner turbo05 Nov 2014
|
|
Turbo Change21 viewsTurbo hoses were upgraded to silicone jobbies05 Nov 2014
|
|
Turbo Change15 viewsDrilling out the old studs05 Nov 2014
|
|
Turbo Change15 viewsGoing Caving05 Nov 2014
|
|
Turbo Change16 viewsWhere is it?!05 Nov 2014
|
|
19 views05 Nov 2014
|
|
17 views02 Nov 2014
|
|
20 views02 Nov 2014
|
|
18 views02 Nov 2014
|
|
EGR replacement20 viewsNew one v old one!25 Aug 2014
|
|
EGR replacement29 viewsUndoing the right hand valve is much easier that the left one.....25 Aug 2014
|
|
EGR replacement17 viewsThese horrible T30 bolts hold the original onto the EGR cooler. Replaced with nice new M8x16mm bolts25 Aug 2014
|
|
EGR replacement19 viewsLeft side - where the hell is it?25 Aug 2014
|
|
EGR replacement19 viewsNew valve in place. Looking nice and shiny!25 Aug 2014
|
|
EGR replacement21 viewsThe left EGR valve is tight up against the turbo boost pipe. This make insertion of the long bolts difficult!25 Aug 2014
|
|
EGR replacement16 viewsBack of left EGR cooler was a swine to replace the clip. Bound it with wire before using pincers to clip together.25 Aug 2014
|
|
EGR replacement21 viewsNew one in place. Old T30 bolts used on top replacing old rusty ones. Good access here!25 Aug 2014
|
|
EGR replacement14 viewsWhile doing stuff on the engine. Good idea to clean yer MAF. Brake cleaner and air used to get it clean again25 Aug 2014
|
|
EGR replacement19 viewsOpening the actuator for inspection.25 Aug 2014
|
|
EGR replacement19 viewsOpening up the actuator reveals that all was OK. Even the ball races are OK25 Aug 2014
|
|
EGR replacement17 viewsOld value with soot cleaned off with wire brush!25 Aug 2014
|
|
EGR replacement17 viewsCarbon build up under the flange in the sliding shaft25 Aug 2014
|
|
Old black stuff comes out13 views04 Jun 2014
|
|
Draining the last bit out of the sump15 views04 Jun 2014
|
|
Weep around the Mechatronic Plug....12 views04 Jun 2014
|
|
Millers Millermatic DM Premium ATF going in via the funnel13 views04 Jun 2014
|
|
The good stuff going into the oil cooler11 views04 Jun 2014
|
|
Using the stepladder method as approved by Oswiperus!15 views04 Jun 2014
|
|
Using the Hawkeye to check transmission temp - getting there...13 views04 Jun 2014
|
|
Checking the final level at the drain plug14 views04 Jun 2014
|
|
New General Grabber ATs fitted today (14.1.2013)26 views14 Jan 2013
|
|
4 new General Grabber ATs suppled by these guys in Colchester36 views14 Jan 2013
|
|
Lights on dashboard!25 views12 Jan 2013
|
|
Display showing suspension lowering!24 views12 Jan 2013
|
|
Managed to hold the rubber bit with an old spanner23 views18 Nov 2012
|
|
It's finally off36 views18 Nov 2012
|
|
Sawn right thru the bolt and bush sleeve20 views17 Nov 2012
|
|
Sawn off bush18 views17 Nov 2012
|
|
15 views17 Nov 2012
|
|
Old front lower wishbone26 views17 Nov 2012
|
|
New rear brakes24 views10 Nov 2012
|
|
|
|
|
|
|
