Difference between revisions of "IIDTool Common Tasks"

From DISCO4.COM Knowledge Base
Jump to: navigation, search
m (→‎Reset Service Interval Indicator)
 
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
== Reset Service Interval Indicator ==
 +
Navigate to ''Service/Test -> Instrument Pack -> Reset Service Int. Ind. -> Reset Oil''
 +
 +
If the engine is running you will be prompted to turn the engine off and return key to position 2. After pressing Resume, interval will be reset.
 +
 
== Monitoring Battery Voltage ==
 
== Monitoring Battery Voltage ==
 
Starting with IIDTool v2.18, you don't need to do ANYTHING to monitor battery voltage. Plug your IIDTool in the diagnostics port and wait. There is no need to enter any menus. After the tool boots up you will see "IIDTool Ready" on the LCD, which will soon change into the battery voltage live value.
 
Starting with IIDTool v2.18, you don't need to do ANYTHING to monitor battery voltage. Plug your IIDTool in the diagnostics port and wait. There is no need to enter any menus. After the tool boots up you will see "IIDTool Ready" on the LCD, which will soon change into the battery voltage live value.
  
 
== Check FBH Operation ==
 
== Check FBH Operation ==
−
Navigate to Main Menu -> Service/Test -> Auxiliary Heater -> Check Operation.
+
Navigate to ''Main Menu -> Service/Test -> Auxiliary Heater -> Check Operation''.
−
You will be prompted "Proceed with current routine?". Press + to confirm. LCD readout will change to "Waiting 1s" and will count up the time. During the next 2 or 3 minutes the FBH will start up and run for a little while (around 1 minute?) regardless of the fuel level, outside temperature or coolant temperature. If successful you will get "Operation Succeeded" after a few minutes. During these few minutes you can physically confirm it's working by (please be careful it might get VERY hot):
+
You will be prompted "Proceed with current routine?". Press + to confirm.  
 +
 
 +
LCD readout will change to "Waiting 1s" and will count up the time.  
 +
 
 +
During the next 2 or 3 minutes the FBH will start up and run for a little while (around 1 minute?) regardless of the fuel level, outside temperature or coolant temperature.  
 +
 
 +
If successful you will get "Operation Succeeded" after a few minutes.  
 +
 
 +
During these few minutes you can physically confirm it's working by (please be careful it might get VERY hot):
 +
 
 +
1. Putting your hand or ear close to the FBH (if still not very hot you can even touch it). You will hear it working and it will start getting hot.
  
−
1. Putting your hand close to the FBH (if still not very hot you can even touch it)
 
 
2. Finding the exhaust outlet near the left front wheel arch and putting your hand close to the outlet, it will be blowing relatively hot air
 
2. Finding the exhaust outlet near the left front wheel arch and putting your hand close to the outlet, it will be blowing relatively hot air
  
 
== Activate 4x4 Info ==
 
== Activate 4x4 Info ==
−
'''Discovery 3'''
+
See [[IIDTool_Car_Config_File_Editing|Car Configuration Editing]]
−
 
 
−
Navigate to Main Menu -> Car Config -> Select ECU -> Audio System -> Type - Multimedia Module.
 
−
Press + to set to High. Press back multiple times to exit the Car Config menu. Change will be detected and you will be prompted to confirm. Follow the on screen instructions (LEAVE THE KEY ON while the LCD display goes off for a few seconds etc etc). When done, for 4x4 Info to be available, you need to turn the car off and let the parking brake light go out. Upon restart, 4x4 info will be available.
 
  
  
 
Back to [[IIDTool]]
 
Back to [[IIDTool]]

Latest revision as of 08:48, 4 February 2014

Reset Service Interval Indicator

Navigate to Service/Test -> Instrument Pack -> Reset Service Int. Ind. -> Reset Oil

If the engine is running you will be prompted to turn the engine off and return key to position 2. After pressing Resume, interval will be reset.

Monitoring Battery Voltage

Starting with IIDTool v2.18, you don't need to do ANYTHING to monitor battery voltage. Plug your IIDTool in the diagnostics port and wait. There is no need to enter any menus. After the tool boots up you will see "IIDTool Ready" on the LCD, which will soon change into the battery voltage live value.

Check FBH Operation

Navigate to Main Menu -> Service/Test -> Auxiliary Heater -> Check Operation. You will be prompted "Proceed with current routine?". Press + to confirm.

LCD readout will change to "Waiting 1s" and will count up the time.

During the next 2 or 3 minutes the FBH will start up and run for a little while (around 1 minute?) regardless of the fuel level, outside temperature or coolant temperature.

If successful you will get "Operation Succeeded" after a few minutes.

During these few minutes you can physically confirm it's working by (please be careful it might get VERY hot):

1. Putting your hand or ear close to the FBH (if still not very hot you can even touch it). You will hear it working and it will start getting hot.

2. Finding the exhaust outlet near the left front wheel arch and putting your hand close to the outlet, it will be blowing relatively hot air

Activate 4x4 Info

See Car Configuration Editing


Back to IIDTool

Retrieved from "http://disco4.com/mediawiki/index.php?title=IIDTool_Common_Tasks&oldid=973"