Advertise on DISCO4.COM
Forum · Gallery · Wiki · Shop · Sponsors
DISCO4.COM > In Car Electronics (D3)

Android 7” screen install help
Post Reply  Down to end
Page 2 of 2 <12
McAdam
 


Member Since: 21 Nov 2020
Location: Canary Islands
Posts: 129

Spain 2005 Discovery 3 4.4 V8 HSE Auto Zambezi SilverDiscovery 3

Can you take a picture of the connector and any cables coming out of it.

There should already be RCA connectors on there (Female). Just connect there, then cut and splice into aux connector on back of factory unit.

If there are no cables, then from your diagrams youre looking at pins: Connector B, pin 11 to Aux Ground + Shield, Pin 12 to Aux L and Pin 13 to Aux R.


The wires labeled as AUX on the 7" unit are for an audio INPUT INTO the new unit.
You need to use the ones labeled as RCA, as these are the OUTPUT from the 7" unit.
 Pre-Production
D3 V8 #264
LHD '04 HSE
Living its life as a 50/50 On/Off road car exploring the Canary Islands 
 
Post #22083516th Feb 2021 11:57 am
View user's profile Send private message View poster's gallery Reply with quote
Oillybob55
 


Member Since: 12 Jul 2020
Location: Bradford
Posts: 42

United Kingdom 2008 Discovery 3 TDV6 XS Manual Zambezi SilverDiscovery 3







Looking at the cables I am assuming I only need the audio out. What’s the P.CONT CVBS IN1 and AV-out
 Discovery 3 XS 2008 Manual Zambezi Silver  
Post #22084816th Feb 2021 8:28 pm
View user's profile Send private message View poster's gallery Reply with quote
McAdam
 


Member Since: 21 Nov 2020
Location: Canary Islands
Posts: 129

Spain 2005 Discovery 3 4.4 V8 HSE Auto Zambezi SilverDiscovery 3

Yup, you only need Audio Out.
P.Cont is for the handbrake, its designed to comply with regulations.
Use of the device "Should" be limited to when the handbrake is applied.
But this can usually be configured in the settings.
I Ignored that wire.

CVBS IN1 is for a video input.
And AV Out is for secondary screens, but Im not sure what it would display on them.
 Pre-Production
D3 V8 #264
LHD '04 HSE
Living its life as a 50/50 On/Off road car exploring the Canary Islands 
 
Post #220966211th Feb 2021 10:50 am
View user's profile Send private message View poster's gallery Reply with quote
Oillybob55
 


Member Since: 12 Jul 2020
Location: Bradford
Posts: 42

United Kingdom 2008 Discovery 3 TDV6 XS Manual Zambezi SilverDiscovery 3

Hi all

I have the unit wired in and it’s working with a couple of issues.

1. The sound is really quite even with the new unit up full and the stereo.

2. When I get or make a call the person can hear me but I can’t hear them.

Any ideas on what it could be?

Cheers
 Discovery 3 XS 2008 Manual Zambezi Silver  
Post #22158147th Mar 2021 1:58 pm
View user's profile Send private message View poster's gallery Reply with quote
Oillybob55
 


Member Since: 12 Jul 2020
Location: Bradford
Posts: 42

United Kingdom 2008 Discovery 3 TDV6 XS Manual Zambezi SilverDiscovery 3

Thinking about this is it because I have connected into the Aux straight in the rear of stereo before the amp?
 Discovery 3 XS 2008 Manual Zambezi Silver  
Post #22158267th Mar 2021 2:48 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 2 of 2 <12
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO4.COM is independent and not affiliated to Land Rover.
Switch to Mobile Site