| Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Groups · Profile · Donate ·
Log In
|
- You are currently viewing DISCO4.COM as a guest - Register to take part or Log In
AndrewS
Tarquin of the Desert
Member Since: 06 May 2005
Location: Y...... because I can
Posts: 10442
|
DiscoDunc wrote:I guess you have to winch slower wioth plasma then and give the winch time to cool.
And unwind the rope off the drum. We did this Morocco as a 'just in case'.
http://www.flickr.com/photos/madelynhardma...744071138/ In the Beginning there was nothing, which exploded.
|
 11th Mar 2008 6:47 pm |
|
|
Slimer
Site Moderator
Member Since: 06 Jan 2005
Location: Last Exit to Nowhere
Posts: 16295
|
Spool synthetic ropes out after winching (and during the tea/beer break on a long session) so they don't melt and don't act as insulation whilst the winch cools down The End
|
| 11th Mar 2008 6:48 pm |
|
|
Non Stick Nick
Member Since: 02 Oct 2005
Location: Reading, Berkshire
Posts: 772
 
|
I am curious about the heat build up on an electric winch.
I know that numerous models have the brake in the middle of the drum.
Several manufacturers advise against prolonged periods of “winching out†because this will understandably generate heat in the drum.
Are we saying here that prolonged winching in will produce enough heat from the electric motor to heat the drum enough to melt the plasma?
Also, bearing in mind Andrews comments that plasma + electric winch is fine on 110’s yet heat is an issue for a D3, does this not pose the question that the winch is being asked to do too much and that alternative rigging or a bigger winch is needed?
I must admit that I have done a fair bit of winching over the years yet head build up on the D3 (or any vehicle to which the winch has been fitted) with a X9+ & dynema has never been an issue.
In the general debate though, it’s plasma every time for me!
Regards to all.
Non Stick I am a hob nobber.
|
| 12th Mar 2008 9:20 am |
|
|
AndrewS
Tarquin of the Desert
Member Since: 06 May 2005
Location: Y...... because I can
Posts: 10442
|
Non Stick Nick wrote:
Are we saying here that prolonged winching in will produce enough heat from the electric motor to heat the drum enough to melt the plasma?
Also, bearing in mind Andrews comments that plasma + electric winch is fine on 110’s yet heat is an issue for a D3, does this not pose the question that the winch is being asked to do too much and that alternative rigging or a bigger winch is needed?
Yep and it does not have to be prolonged  The Warn xp 9.5 winch which is standard LR spec for a D3 IMO is not up to the job. I had plasma on my D3 but have gone back to steel. A bigger winch or hydraulic is the way to go  In the Beginning there was nothing, which exploded.
|
| 12th Mar 2008 11:06 am |
|
|
Non Stick Nick
Member Since: 02 Oct 2005
Location: Reading, Berkshire
Posts: 772
|
Bigger it is then. Don't want to start another thread but don't rate hydraulics unless we are talking commercial models.
Ncik I am a hob nobber.
|
| 12th Mar 2008 11:18 am |
|
|
Ken
Member Since: 20 Feb 2006
Location: Here
Posts: 10865
|
Ryder 12000lb fooking great
|
| 12th Mar 2008 1:25 pm |
|
|
10forcash
Member Since: 09 Jun 2005
Location: Ubique
Posts: 16534
|
Yep, agree with that Ken - well I would, wouldn't I? 
|
| 12th Mar 2008 1:40 pm |
|
|
christyler
Member Since: 31 Dec 2005
Location: Cork, Ireland
Posts: 1168
 
|
Slimer wrote:So why have you got a roller fairlead with a synthetic rope Dunc? 
Good Point, Rollers are the quickest way to damage the plasma line. If pulling slightly sideways the plasma line will get trapped in the edge of the rollers and start tearing, this will cause damage and subsequent failure.
Dunc,
Change them rollers !! CLUB "Ah Shor it'll be grand"
First D3 in the World with a Hydraulic Winch.
2006 Disco 3 TDV6 S Auto,
Diff Locks, Turbochipped, Raised Air Intake, 220volts Onboard, Onboard Compressor, Large Bore Exahust, Underbody Protection, One or two Other Mods as well.
Other toys include, Argo Avenger 8x8, Tatra 6x6 Motorhome (Being Built)
|
| 12th Mar 2008 2:11 pm |
|
|
DiscoDunc
Member Since: 08 May 2006
Location: Bristol
Posts: 16390
  
|
Thanks, I'll change the weekend Duncan
-----------------------------------------------------
If I'd known I was going to be so thirsty this morning I'd have drunk more beer last night.
FFRR Autobiography 4.4 SDV8 MY17
D4 HSE MY13 SOLD
FFRR 3.6 Vogue TDV8 SOLD
D4 HSE MY10 SOLD
D4 SE TECH MY15 SOLD
D4 XS MY12 SOLD
D4 HSE MY10 SOLD
D3 HSE MY06 - Re-Cycled Worldwide
|
| 12th Mar 2008 7:18 pm |
|
|
simon
Member Since: 11 Jan 2005
Location: Shropshire
Posts: 18296
|
DiscoDunc wrote:Thanks, I'll change the weekend
Wow ! With a power like that, can you play the lottery for me
|
| 12th Mar 2008 7:20 pm |
|
|
10forcash
Member Since: 09 Jun 2005
Location: Ubique
Posts: 16534
|
simon wrote:DiscoDunc wrote:Thanks, I'll change the weekend
Wow ! With a power like that, can you play the lottery for me
Think he meant his undercrackers
|
| 12th Mar 2008 7:26 pm |
|
|
simon
Member Since: 11 Jan 2005
Location: Shropshire
Posts: 18296
|
10forcash wrote:Think he meant his undercrackers
Are they made of plasma too then 
|
| 12th Mar 2008 7:30 pm |
|
|
10forcash
Member Since: 09 Jun 2005
Location: Ubique
Posts: 16534
|
I have no idea or wish to find out
|
| 12th Mar 2008 7:44 pm |
|
|
|
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
|
|
DISCO4.COM is independent and not affiliated to Land Rover.
