Member Since: 25 Dec 2016
Location: NORWAY
Posts: 196
Maybe I was not quite right. Don't think the car missed the ECU, but at least the IID Tool didn't find it, therefore no codes. Not sure honestly.
Somehow I found a "refresh" or identify ECU's. And then it popped up again. With codes of course.
I also drove a long time without the fuse, kept the alarm away
25th Mar 2019 9:44 pm
graymattor
Member Since: 26 Nov 2018
Location: Retford
Posts: 4
Right I've borrowed a GAP IID Tool, and it found faults with the EPB, the code was C1A47-01(FB) Force Sensor Electrical fault! I've done a bit of googling and it's come up with next to nothing, does anyone know what could cause this? Can it be a broken wire or is it the force sensor that's failed? Can it be replaced or is it a full new unit?
Member Since: 09 Apr 2018
Location: essex
Posts: 11
handbrake failure
just need to know if i pull the release cable am i going to have to pull a fuse to stop hand brake applying when i take key out? mine wont release, its a manual. cheers.
13th Apr 2019 10:57 am
ianm27
Member Since: 02 Jun 2016
Location: Hertfordshire
Posts: 2154
Someone with more knowledge will be along shortly but I would say yes, you would need to pull the fuse to stop the EPB trying to re-engage.Uncle Ray's spare wheel protector
Limo Tint
Blackvue front & rear dashcam
Cruise control switch pack
Bodsy's remote for FBH
13th Apr 2019 12:26 pm
macko
Member Since: 09 Apr 2018
Location: essex
Posts: 11
meant to say its a disco 3......not sure if its the same as the disco 4?? pardon my ignorance!!
i WAS going to say the fault is the D missing in the title of this thread BUT i've noticed the thread is coming up to 10 years old, so i can't blame you Macko !
13th Apr 2019 4:14 pm
MatcherMike
Member Since: 15 Sep 2012
Location: Gloucestershire
Posts: 94
Hi all,
Sorry, cant find the info on here.
What's the best way to get the epb module off the vehicle so I can work on it please? I had to pop the emergency release so needs setting up and repairing.
8 torx screws are corroded so too difficult to do in situ.
Thanks
Mike
27th Aug 2019 6:08 pm
gearmuncher
Member Since: 30 Oct 2018
Location: Woodley
Posts: 143
there is a youtube video.
27th Aug 2019 8:04 pm
LandyIRL
Member Since: 24 Mar 2016
Location: Galway
Posts: 123
Handbrake module cycling in and out after replacement
I replaced a HB module (rebuilt one) on a manual D3 (on coil springs) and adjusted it up after. The handbrake would not go into bedding in mode for the brake shoes and there is the red light and the amber brake shoes light on and the usual error. The HB when i try it (as if for bedding in) is activating if i hold it and stopping the vehicle but not staying on when stationary. It cycles in and out several times before stopping. I had cleared the faults and still lights flashing. There were other lights like the steering angle sensor etc and i reset the xyz switch and cleared them though now i am seeing a clutch sensor fault on the fault reader in the EPB module which doesn't clear. I replaced the EPB switch with a new one and saw someone had been at the wires on this before and doing some repair work.
Any ideas as to why the EPB is repeatedly cycling in and out and not engaging to hold ?
24th Jan 2020 6:17 pm
gearmuncher
Member Since: 30 Oct 2018
Location: Woodley
Posts: 143
the EPB module has a torque sensor, different torque for different situations, sounds like this is not working, are the brakes actually coming on ?.
I think a IID or nanocom will show the torque value.
26th Jan 2020 4:42 pm
blakemore333
Member Since: 17 Jan 2020
Location: Shrewsbury
Posts: 11
Just joined the EPB fault club
Mine has come up with the yellow warning light on the dash, but it still works manually and isn't making any weird noises.
Really dont want to go to a garage and be charged £££!
Anybody in Shropshire know how to fix this? D4 Barolo Black
31st Jan 2020 2:05 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5042
Sounds like the XY sensor might need recalibrating. Have you noticed the gear position indicator on the dash change? Or the reverse lights not working?yµ (idµ - eAµ) ψ=mψ
31st Jan 2020 2:38 pm
blakemore333
Member Since: 17 Jan 2020
Location: Shrewsbury
Posts: 11
well it did change to jut display E. but now its sorted its self out and the gear numbers display.
However dont know if the reverse light comes on.
I have tried the calibration where you start in reverse, go through all the gears till they display on the dash, turned the ignition off. but that hasn't done anythingD4 Barolo Black
31st Jan 2020 2:42 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5042
Are the digits displayed in full size? Sometimes you might have to do the recalibration more than once if using the manual method as its easy to make a mistake. Beyond that you will need diagnostics read so you should consider a GAP IID or similar if you're going to be running a D3 long term!yµ (idµ - eAµ) ψ=mψ
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
