lynalldiscovery
Member Since: 22 Dec 2009
Location: Maidstone
Posts: 7274
  
|
Is the belt a genuine one? Im not saying you must have genuine, just grabbing at straws.
|
 1st Apr 2016 3:38 pm |
|
|
Lee333
Member Since: 19 Jan 2016
Location: Chichester
Posts: 30
 
|
Gates one from an auto factor. The one I took off was a dayco one I think.
|
| 1st Apr 2016 4:08 pm |
|
|
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20841
 
|
Lee333 wrote:Only when I turn the steering wheel. It does it 80% of the time. Sometimes not at all but very rarely. And when I go over speed bumps. Apart from that it's silent when driving and when sat still either on idle or revved.
I wonder if it's a seized/partially seized/rusty ball joint, if it's ONLY when turning the steering wheel, or large movements of the suspension 
How long was the car sat around for before the engine was swapped over? My D3 Build Thread
TDV8 Retrofit Build Thread
|
| 1st Apr 2016 5:39 pm |
|
|
Lee333
Member Since: 19 Jan 2016
Location: Chichester
Posts: 30
|
Was sat up for a while jacked up with the front wheels in the air.
Good couple of months I'd say.
It does only happen as soon as you turn the steering wheel. The noise sounds like it's coming from the front of the engine tho ?
Unless if something is seized like the ball joint , the engine is working harder to turn the pulley on the steering pump to enable the wheel to turn causing the belt to slip slightly ?? Or am I looking into it to deep ??
|
| 1st Apr 2016 6:21 pm |
|
|
lynalldiscovery
Member Since: 22 Dec 2009
Location: Maidstone
Posts: 7274
|
Lee333 wrote:Gates one from an auto factor. The one I took off was a dayco one I think.
I dont suppose you checked it against the old one before fitting?
Does the belt feel nice and tight ie springy when you push against it, doing this also should move the tensioner.
|
| 1st Apr 2016 6:22 pm |
|
|
Lee333
Member Since: 19 Jan 2016
Location: Chichester
Posts: 30
|
Yes mate I checked it if anything the new one was 2mm smaller. Yes it's tight mate. All seems good. That's why me and now quite a few others are confused ?!
|
| 1st Apr 2016 6:36 pm |
|
|
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20841
|
Lee333 wrote:Was sat up for a while jacked up with the front wheels in the air.
Good couple of months I'd say.
It does only happen as soon as you turn the steering wheel. The noise sounds like it's coming from the front of the engine tho ?
Unless if something is seized like the ball joint , the engine is working harder to turn the pulley on the steering pump to enable the wheel to turn causing the belt to slip slightly ?? Or am I looking into it to deep ??
The noise may be echoing underneath the car, making it appear as though it's from the engine
Doesn't take long to access the ball joints and check them  My D3 Build Thread
TDV8 Retrofit Build Thread
|
| 1st Apr 2016 6:54 pm |
|
|
Lee333
Member Since: 19 Jan 2016
Location: Chichester
Posts: 30
|
Sounds like a job for tomorrow morning.
I'll get it in the workshop and have a look.
Thanks for your help guys
|
| 1st Apr 2016 7:05 pm |
|
|
PeterTh
Member Since: 06 Sep 2013
Location: Alunda
Posts: 330
  
|
Mine is squeking even if I don´t start the engine before turning the wheels or bouncing it up and down on the bumper so engine related noise seems unlikely in my case. Disco_Mikey (  ), do you mean the balljoints on the upper and lower arms? I suspect my problem originates from the front upper arm balljoints as lower arms are changed not long ago and I can´t really see anything else that moves when turning the wheels. As my car is at 150.000 miles I have desided to change all remaining arms, front and rear and also all the struts. Lee, do you get the squeks without starting the engine as well?
//Peter 2011 Discovery 4 3.0 TDV6 S Automatic
1999 Discovery 2 V8 ES Automatic
Earlier
2006 Discovery 3 TDV6 SE Automatic
1996 Discovery 300 Tdi ES Automatic
1975 Series 3 2.25 diesel
Nanocom Evolution for D2 V8, D3 and D4
Working kelpies for working the sheep
 
|
| 1st Apr 2016 8:26 pm |
|
|
Lee333
Member Since: 19 Jan 2016
Location: Chichester
Posts: 30
|
No mate. , mines on 120k , only squeaks when I turn the steering wheel. It's a really strange noise.
The missus is off work tomorrow so I'll video it while she turns the wheel and upload it via you tube. Might help out a bit.
|
| 1st Apr 2016 8:35 pm |
|
|
PeterTh
Member Since: 06 Sep 2013
Location: Alunda
Posts: 330
|
The sound I have is very simlar to an old iron bed with springs which really needs some lube...
//Peter 2011 Discovery 4 3.0 TDV6 S Automatic
1999 Discovery 2 V8 ES Automatic
Earlier
2006 Discovery 3 TDV6 SE Automatic
1996 Discovery 300 Tdi ES Automatic
1975 Series 3 2.25 diesel
Nanocom Evolution for D2 V8, D3 and D4
Working kelpies for working the sheep
|
| 1st Apr 2016 8:40 pm |
|
|
|
|
Lee333
Member Since: 19 Jan 2016
Location: Chichester
Posts: 30
|
My noise is similar Peter
Doesn't make the noise with engine off Mike
|
| 1st Apr 2016 8:50 pm |
|
|
danj3000
Member Since: 23 May 2019
Location: Bristol
Posts: 5
|
Picking up on this now old thread but wanted to post as I have recently had a similar issue.
Replaced the belts and two tensioners with INA products and whilst the tensioners are nice and quiet, I was getting a tapping/light squeal noise from the belt area when turning the wheel left to right. Power steering is all fine.
I've now replaced the belt with a genuine LR one and the noise has gone.
The genuine belt has a slight texture to the back of it which the one in my INA kit doesn't. So either this difference or the INA kit belt was fractionally too small, causing unnecessary strain on the pulleys and thus the noise.
|
| 16th May 2024 7:05 pm |
|
|
