Member Since: 11 Sep 2016
Location: Marnoch
Posts: 4244
If you fill in your model details in your profile that might help as the we can see if your trying to put an HSE unit into a base model (which may not have all the wires you need so you may need to take feeds off other circuits… )
I want to see the sweets before I get into your windowless van... I'm not stupid!
Corris Grey D4 Commercial SE 2016
Zermatt Sliver 2007 D3 SE manual (gone)
Indus Silver D4 HSE 2015 (gone)
Bonatti Grey D3 HSE 2006 (gone)
White D3 S (LHD) 2007 (gone)
Firenze Red D4 HSE 2014 (gone)
Black RRS 3.6TDV8 2008 (gone)
Rusty Green Defender 110 1997 (gone)
Black FL2 HSE 2013 (gone)
18th Sep 2021 8:54 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10683
Pin 11 then. Whatever colour is on that
18th Sep 2021 9:34 pm
R1wilky
Member Since: 15 Sep 2021
Location: Durham
Posts: 93
pin purple/green 2-3 black 4-5 empty 6 black 7 tan 8-9-10 empty
pin 11 green 12 red 13 empty 14 yellow 15 green 16 black 17 green
pins 6-7 17 are in a black sleeve
19th Sep 2021 6:48 am
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10683
Did you get the dvd map drive from under passenger seat ?
This is require for Nav
Member Since: 15 Sep 2021
Location: Durham
Posts: 93
Yeah got the drive all wiring from front to back and the logic 7 amp with the speaker plug everything is plug and play apart from the screen wiring I had to cut them off the main loom behind the dash
19th Sep 2021 8:42 am
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10683
To get the display to do anything useful the following is required:
1) The upgraded 6CD player head unit
2) The orange optical fibre connectors. All connectors must be plugged into devices, and all devices powered up.
3) You probably need to edit the car config to tell the car is has new equipment. This is done with a GAP IID £500
4) you need to power the display with the 4 wires.
pins 2 and 3 blacks to ground
Red not required.
pin 1 Blue/purple Fuse 53
pin 11 Blue (or green colour in your case) fuse 56
To get nagivation working you require:
5) The DVD drive under the passenger seat, with D3 DVD in it
6) The grey cable with blue connectors between the drive and display to show map images etc.
7) Connect 2 lots of yellow the green wires between the DVD drive and display. (for communication/touch screen inputs and audio directions)
8) 2 lots of power for the DVD Drive
9) speed MPH input (available under drivers seat) green wire
10) Antenna for car location on purple connector. In tail gate or a shark fin, or £10 ebay internal one
11) You probably need to edit the car config to tell the car is has new equipment. This is done with a GAP IID £500
19th Sep 2021 8:50 am
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10683
DISPLAY GREY PLUG CONNECTIONS
pin 1 purple/green +12v fuse 53
2-3 black ground both
4-5 empty
pins 6-7 17 are in a black sleeve. To Map DVD drive for Audio directions
6 black the cable braid/screen to DVD drive pin 31
7 tan (or yellow) to DVD drive pin 14
17 green to DVD drive pin 30
8-9-10 empty
11 green (or blue) fuse 56
12 red Not required
13 empty
14 yellow to DVD drive pin 22
15 green to DVD drive pin 6
16 black mistake?
Click image to enlarge
19th Sep 2021 9:06 am
R1wilky
Member Since: 15 Sep 2021
Location: Durham
Posts: 93
just on pulling it apart and in the os rear quarter the nokia module is their with optic cables in it the loom i have dosnt have it they were in the front each side of the radio pics to follow
19th Sep 2021 12:00 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10683
rear nokia units are better (if you have the wiring)
You don't have to fit it though, but you can't leave the orange optic connector unplugged
19th Sep 2021 12:51 pm
R1wilky
Member Since: 15 Sep 2021
Location: Durham
Posts: 93
Left plug in car drivers kick panel left is new plug
19th Sep 2021 1:03 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10683
Click image to enlarge
So your car has nokia unit in the rear.
The nav wiring you have has, has nokia unit at the sides. This is dealer accessory.
I don't know enough about phone wiring to say what to do.
If the rear phone wiring is seperate, you could leave that installed too?
Last edited by Pete K on 19th Sep 2021 1:44 pm. Edited 1 time in total
19th Sep 2021 1:08 pm
R1wilky
Member Since: 15 Sep 2021
Location: Durham
Posts: 93
are the other wires the ones for the screen as they look the same apart for i have green it has blue
mine has the phone unit in the centre consul the phone cables are just taped to the loom so ill pick them off everything else looks ok more pics to follow
Last edited by R1wilky on 19th Sep 2021 1:20 pm. Edited 1 time in total
19th Sep 2021 1:10 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10683
EDIT: Oh I dunno. Could be. Probably
You seam to have found connector C2247
pins
7,8,9 Nav Audio
4,5 control
pin 3 red supply + phone power
pin 10 blue 'Remote powerup' (fuse 58)
pin 12 nav power ? + (fuse 53)
pin 2 nav ground
Hope these connections line up with the connector you found
Do you use the phone cradle in the arm rest or bluetooth only ?
I would see if you can get the nav working first, and then cut the phone is later.
Last edited by Pete K on 19th Sep 2021 1:56 pm. Edited 5 times in total
19th Sep 2021 1:18 pm
R1wilky
Member Since: 15 Sep 2021
Location: Durham
Posts: 93
blue tooth
19th Sep 2021 1:21 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10683
of that phone wiring from the rear, most of the wires goto the cradle. (which aren't important)
But there are a couple of reds for power pins17/18, a blue pin16 and 2 black grounds pins33/34 which need connection.
So if you can get them connected up, it stands a chance of working
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
